Endress + Hauser Operating Instructions Indumax CLS50/CLS50D

Operating Instructions Indumax CLS50/CLS50D Analog or digital sensors with Memosens protocol For inductive measurement of conductivity in liquids BA00182C/07/EN/15.12 71186405 Documentation information Warnings The structure, signal words and safety colors of the signs comply with the specifications of ANSI Z535.6 ("Product safety information in product manuals, instructions and other collateral materials"). Safety message structure Meaning DANGER Cause (/consequences) Consequences if safety message is not heeded ► Corrective action This symbol alerts you to a dangerous situation. Failure to avoid the situation will result in a fatal or serious injury. WARNING Cause (/consequences) Consequences if safety message is not heeded ► Corrective action This symbol alerts you to a dangerous situation. Failure to avoid the situation can result in a fatal or serious injury. CAUTION Cause (/consequences) Consequences if safety message is not heeded ► Corrective action This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in minor or medium injury. NOTICE Cause/situation Consequences if safety message is not heeded ► Action/note This symbol alerts you to situations that can result in damage to property and equipment. ! ! ! Symbols used Èä1 This symbol indicates a cross reference to a defined page (e.g. p. 1). Èå2 This symbol indicates a cross reference to a defined figure (e.g. fig. 2). Indumax CLS50/CLS50D Table of contents 1 Basic safety instructions . . . . . . 4 1.1 1.2 1.3 1.4 1.5 Requirements for personnel . . . . . . . . . . . . Designated use . . . . . . . . . . . . . . . . . . . . . . Occupational safety . . . . . . . . . . . . . . . . . . Operational safety . . . . . . . . . . . . . . . . . . . Product safety . . . . . . . . . . . . . . . . . . . . . . 2 Identification . . . . . . . . . . . . . . 7 2.1 2.2 2.3 2.4 Type code for versions with Ex approval . . . Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . Temperature classes for hazardous locations Certificates and approvals . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . 9 3.1 3.2 3.3 Installation conditions . . . . . . . . . . . . . . . . 9 Installation . . . . . . . . . . . . . . . . . . . . . . . . 11 Post-installation check . . . . . . . . . . . . . . . 13 4 Wiring . . . . . . . . . . . . . . . . . . 14 4.1 4.2 Connection to the transmitter . . . . . . . . . 14 Wiring diagram for explosion-hazardous areas 15 5 Commissioning. . . . . . . . . . . . 18 6 Maintenance. . . . . . . . . . . . . . 18 7 Spare parts and return . . . . . . 19 7.1 7.2 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . 19 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 8 Technical data . . . . . . . . . . . . 21 8.1 8.2 8.3 8.4 8.5 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . Performance characteristics . . . . . . . . . . . Environment . . . . . . . . . . . . . . . . . . . . . . Process . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical construction . . . . . . . . . . . . . 4 4 4 5 5 7 7 8 8 21 21 22 22 24 9 Appendix . . . . . . . . . . . . . . . . 25 9.1 Declaration of conformity for CLS50-G and CLS50D-BA . . . . . . . . . . . . . . . . . . . . . . . 25 Declaration of conformity for CLS50-V . . . 27 9.2 Endress+Hauser Basic safety instructions 1 Basic safety instructions 1.1 Requirements for personnel Indumax CLS50/CLS50D ► Installation, commissioning, operation and maintenance of the measuring system must only be carried out by trained technical personnel. ► The technical personnel must be authorized by the plant operator to carry out the specified activities. ► The electrical connection may only be performed by an electrical technician. ► The technical personnel must have read and understood these Operating Instructions and must follow the instructions they contain. ► Measuring point faults may only be rectified by authorized and specially trained personnel. Repairs not described in the enclosed Operating Instructions may only be carried out directly at the manufacturer's or by the service organization. 1.2 Designated use Indumax CLS50/CLS50D conductivity sensors are especially suitable for application in the chemical industry and process engineering. The six-decade measuring range and the high chemical resistance of the materials in contact with medium (PFA or PEEK) permit to use this sensor in a number of various applications, e.g.: • Concentration measurement of acids and bases • Quality monitoring of chemical products in tanks and pipes • Phase separation of product/product mixtures Digital CLS50D sensors are used with Liquiline CM44x or Liquiline CM42. Analog CLS50 sensors are used with the transmitters Liquiline CM42, Liquisys CLM223/253 or Mycom CLM153. Any other use than the one described here compromises the safety of persons and the entire measuring system and is not permitted. The manufacturer is not liable for damage caused by improper or non-designated use. NOTICE Use in not specified applications Measurement errors and failures up to the breakdown of the measurement point possible ► Only use the product acc. to it’s specification. ► Note the technical data of the nameplate. 1.3 Occupational safety As the user, you are responsible for complying with the following safety conditions: • Guidelines for explosion protection • Installation instructions • Local prevailing standards and regulations. 4 Endress+Hauser Indumax CLS50/CLS50D 1.4 Basic safety instructions Operational safety ► Before commissioning the entire measuring point, make sure all the connections are correct. Ensure that electrical cables and hose connections are not damaged. ► Do not operate damaged products, and safeguard them to ensure that they are not operated inadvertently. Mark the damaged product as defective. ► If faults cannot be rectified, the products must be taken out of service and secured against unintentional commissioning. 1.5 Product safety 1.5.1 State of the art The sensor has been designed and tested according to the state of the art and left the factory in perfect functioning order. Relevant regulations and European standards have been met. 1.5.2 Safety instructions for electrical equipment in hazardous locations Sensors with ATEX approval (CLS50-G and CLS50D-BA for Zone 0 and CLS50-V for Zone 2) have been developed and manufactured in compliance with applicable European standards and guidelines and are suitable for use in hazardous locations. The Declaration of Conformity confirms compliance with the harmonized European standards for using the sensors in hazardous locations. CLS50-G and CLS50D-BA • The sensors may be operated in Zone 0 (1G) classified locations. • The sensors may be operated in liquid media providing a conductivity of >10 nS/cm, only. • The measurement cable must be protected from electrostatic charging when applied in Ex-Zone 0 (1G). CLS50-G • The sensor may only be connected to the following transmitters: – Mycom type CLM152-Z with transmitter module type FCL1, EC type-examination certificate DMT 99 ATEX E 076 – Mycom type CLM153-G, EC type-examination certificate DMT 01 ATEX E 174 – Liquiline type CM42-IG, EC type-examination certificate EX5 05 03 30266 012 • The maximum permitted length of the measuring cable is 55 m (180 ft). Endress+Hauser 5 Basic safety instructions Indumax CLS50/CLS50D CLS50D-BA • CLS50D is a digital sensor with Memosens protocol. Its connection data are shown in the table below. • The sensor may also be connected to the intrinsically safe Memosens connection of the FSDG1 module of the Liquiline type CM42-LG transmitter, EC type-examination certificate EX5 05 03 30266 012, provided the transmitter Liquiline M CM42-LG is connected to a galvanically isolated power supply. • The maximum permitted length of the measuring cable is 100 m (330 ft). Ui 5.1 V Ii 130 mA Pi 166 mW Ci 18 μF Li 72 μH CLS50-V • The sensor may be operated in Zone 2 (3G) classified locations. • The sensor may only be connected to the following transmitter: Liquiline type CM42-IV, EC type-examination certificate BVS 08 ATEX E 093 • The maximum permitted length of the measuring cable is 55 m (180 ft). Sensors with FM or CSA approval (CLS50-O, CLS50-S) • Observe the documentation and the control drawings of the transmitter. General notes for all sensor types mentioned above • Compliance with the ambient and medium temperature ranges indicated is mandatory to ensure safe operation of the device. • Connection and operation of the sensor must be carried out in compliance with the instructions in the Operating Instructions of the sensor and of the transmitter connected. Observe all operating data of the sensor. • Metallic process connection parts have to be mounted at the mounting location electrostatically conductive (<1 ΜΩ). • Non metallic process connection parts have to be protected from electrostatic charging (even when applied in Ex zone 1 (2G)). • Full compliance with regulations for electrical systems in hazardous locations (EN60079-14) is mandatory when using the devices and sensors. • Make sure the device is mounted correctly to maintain the degree of protection of the housing (use genuine seals, mount the cable entry correctly, tighten the nut)! • The degree of protection only applies when the flange is mounted. 6 Endress+Hauser Indumax CLS50/CLS50D Identification 2 Identification 2.1 Type code for versions with Ex approval Name Type Indumax CLS50 Name Type Indumax CLS50 Name Type Indumax CLS50D 2.2 Version - G x for the use in hazardous locations, ATEX II 1G Ex ia IIC T4/T6 Ga Process connections, material no Ex relevance x x Version - V x x x for the use in hazardous location, ATEX II 3G Ex nL IIC T4/T6 Gc Process connections, material no Ex relevance Version - BA x x x x - x x for the use in hazardous location, ATEX II 1G Ex ia IIC T4/T6 Ga Process connections, material, cable connection, calibration, service no Ex relevance Nameplate The nameplate can be found on the sensor. The following information is provided on the nameplate: • Order code • Extended order code • Serial number • Cell constant (nominal value) • Protection class • Pressure specification at 20 ˚C • Continuous service temperature Compare the data on the nameplate with your order. To find out what CLS50D version you have, enter the order code indicated on the nameplate in the search screen at the following address: www.products.endress.com/order-ident Endress+Hauser 7 Identification 2.3 Indumax CLS50/CLS50D Temperature classes for hazardous locations 2.3.1 CLS50-G Temperature class Sensor Ambient temperature range Ta Medium temperature range Tmed T4 CLS50-G -20 ˚C to +125 ˚C -20 ˚C to +125 ˚C T6 CLS50-G -20 ˚C to +75 ˚C -20 ˚C to +75 ˚C 2.3.2 CLS50D-BA Temperature class Sensor Ambient temperature range Ta Medium temperature range Tmed T4 CLS50D-BA*D CLS50D-BA*C CLS50D-BA*B -20 ˚C to +60 ˚C -20 ˚C to +60 ˚C -20 ˚C to +60 ˚C -20 ˚C to +110 ˚C -20 ˚C to +120 ˚C -20 ˚C to +120 ˚C T6 CLS50D-BA*D CLS50D-BA*C CLS50D-BA*B -20 ˚C to +60 ˚C -20 ˚C to +60 ˚C -20 ˚C to +60 ˚C -20 ˚C to +70 ˚C -20 ˚C to +70 ˚C -20 ˚C to +70 ˚C ► The plant operator must guarantee the compliance with these temperatures by suitable installation measures. 2.3.3 CLS50-V Temperature class Sensor Ambient temperature range Ta Medium temperature range Tmed T4 CLS50-V -20 ˚C to +125 ˚C -20 ˚C to +125 ˚C T6 CLS50-V -20 ˚C to +75 ˚C -20 ˚C to +75 ˚C 2.4 Certificates and approvals 2.4.1 CE conformity Declaration of conformity The product meets the requirements of the harmonized European standards. It thus complies with the legal requirements of the EC directives. The manufacturer confirms successful testing of the product by affixing the 4 symbol. 2.4.2 ATEX approvals CLS50-G and CLS50D-BA II 1G Ex ia IIC T4/T6 Ga 8 Endress+Hauser Indumax CLS50/CLS50D Installation CLS50-V II 3G Ex nL IIC T4/T6 Gc 3 Installation 3.1 Installation conditions 3.1.1 Installation position Install the sensor in such a way that the sensor opening is oriented in the flow direction of the medium. The sensor head must be completely immersed in the medium. a0007035 Fig. 1: Installation position of the sensor 1 2 a Flow direction of medium Minimum water level in the pipe Sensor distance from the pipe wall Endress+Hauser 9 Installation Indumax CLS50/CLS50D 3.1.2 Installation factor In narrow installation conditions, the conductivity measurement is affected by the pipe walls. This effect is compensated by the so-called installation factor. The transmitter corrects the cell constant by multiplication with the installation factor. The value of the installation factor depends on the diameter and the conductivity of the pipe as well as the sensor’s distance from the wall. If the distance from the wall is sufficient (a > 15 mm (0.59"), from DN 80), it is not necessary to consider the installation factor (f = 1.00). If the distance from the wall is smaller, the installation factor increases in case of electrically insulating pipes (f > 1) and decreases in case of electrically conductive pipes (f < 1). The installation factor can be measured using calibration solutions or it can be approximately determined from the following diagram. f 1.40 2 1.20 1.00 1 0.80 0 5 10 15 20 0.20 0.39 0.59 0.79 25 a [mm] 0.98 a [inch] a0005441 Fig. 2: Relationship between installation factor f and distance from wall a 1 2 Electrically conductive pipe wall Insulating pipe wall 3.1.3 Air set CLS50 To compensate residual coupling in the cable and between the two sensor coils, you must perform a zero calibration in air ("air set") before installing the sensor. For further information, refer to the Operating Instructions of your transmitter. CLS50D The digital sensor is already adjusted at the factory, an on-side compensation is not necessary. 10 Endress+Hauser Indumax CLS50/CLS50D 3.2 Installation Installation 3.2.1 Flange installation The sensor is suitable for installation in T-pieces ≥ DN 80 with the outgoing diameter reduced to ≥ DN 50. ! WARNING Leakages Danger of injuries by leaking medium ► Tighten the nut with a torque of 20 Nm. ► To avoid leakages, regularly check the tightness of the nut. 3.2.2 Flange, not in contact with medium a0007062 Fig. 3: Fixed flange, in contact with medium (order option "process connection": 3, 4) 1 Flange (stainless steel) 3 O-ring 2 Nut 4 Sensor Endress+Hauser 11 Installation Indumax CLS50/CLS50D 3.2.3 Flange, not in contact with medium a0007061 Fig. 4: 1 2 3 Fixed flange, not in contact with medium (order option "process connection": 5, 6, 7) Flange (stainless steel) 4 O-ring Nut 5 Sensor Sealing disk (GYLON) 3.2.4 Lap-joint flange, not in contact with medium a0007063 Fig. 5: 1 2 3 12 Lap-joint flange, not in contact with medium (order option "process connection": A, B, C) Lap-joint flange (PP-GF) 4 O-ring Nut (stainless steel) 5 Sensor Flange (PVDF) Endress+Hauser Indumax CLS50/CLS50D Installation 3.2.5 Assembly installation a0007064 Fig. 6: Installation of sensor with assembly 1 CLA111 with suspension bracket 2 CLA111 with flange connection 3.3 3 4 CLA140 with flange connection CYA611 Post-installation check ► Are sensor and cable undamaged? ► Is the installation position correct? Arrow on the threaded sleeve shows the flow direction = installation position. ► Is the sensor installed via process connection and not suspended from the cable? Endress+Hauser 13 Wiring 4 Indumax CLS50/CLS50D Wiring ! WARNING Device is energized Improper connection can cause injury or death. ► The electrical connection must only be carried out by a certified electrician. ► Technical personnel must have read and understood the instructions in this manual and must adhere to them. ► Prior to beginning any wiring work, make sure voltage is not applied to any of the cables. 4.1 Connection to the transmitter The sensor is supplied with a fixed cable. The connection to the transmitter can be extended using the CYK11 (CLS50D) or the CLK6 (CLS50) special measuring cable (not applicable for use in hazardous locations). RD RD BU RD BU GN WH YE BN n.c. a0017984 Fig. 7: CYK11 for cable extension for CLS50D –max. total cable length: 100 m (330 ft) Pt 100 WH a0012998 Fig. 8: CLK6 for cable extension for CLS50 –max. total cable length: 55 m (180 ft) Please note that the residual coupling increases when the cable is extended. 14 Endress+Hauser Indumax CLS50/CLS50D 4.2 Wiring Wiring diagram for explosion-hazardous areas 4.2.1 Sensors for Zone 0 a0017985 Fig. 9: Connection in hazardous location Endress+Hauser 15 Wiring Indumax CLS50/CLS50D a0013258 Fig. 10: Connection in hazardous location 16 Endress+Hauser Indumax CLS50/CLS50D Wiring 4.2.2 Sensors for Zone 2 EX 4...20 mA Ex nL Zone 2 II 3G EX CLS50 a0010316 Fig. 11: Connection in hazardous location Endress+Hauser 17 Commissioning 5 Indumax CLS50/CLS50D Commissioning Before first commissioning, check if: • the sensor is correctly installed • the electrical connection is correct. If using an assembly with automatic cleaning, check the correct connection of the cleaning agent (e.g. water or air). ! WARNING Incorrect connection of a cleaning unit to an assembly Danger of medium leaking off ► Before applying compressed air to an assembly with cleaning facility, make sure the connections are correctly fitted. Otherwise, the assembly may not be inserted into the process. 6 Maintenance ! WARNING Burning chemicals Danger of chemicals burns to the eyes and skin. Danger of damage to clothing and equipment. ► It is absolutely essential to protect the eyes and hands properly when working with acids, bases and organic solvents! ► Wear protective goggles and safety gloves. ► Clean away splashes on clothes and other objects to prevent any damage. ► Pay particular attention to the information provided in the safety data sheets for the chemicals used. Clean away fouling on the sensor as follows depending on the particular type of fouling: • Oily and greasy films: Clean with grease remover, e.g. alcohol, acetone, as well as hot water and dishwashing detergent if necessary. • Lime and metal hydroxide buildup: Dissolve buildup with diluted hydrochloric acid (3 %) and then rinse thoroughly with plenty of clear water. • Sulfidic buildup (from flue gas desulfurising or sewage treatment plants): Use a mixture of hydrochloric acid (3 %) and thiocarbamide (commercially available) and then rinse thoroughly with plenty of clear water. • Buildup containing proteins (e.g. food industry): Use a mixture of hydrochloric acid (0.5 %) and pepsin (commercially available) and then rinse thoroughly with plenty of clear water. 18 Endress+Hauser Indumax CLS50/CLS50D Spare parts and return 7 Spare parts and return 7.1 Spare parts Pos. no. Spare part kit Order no. 150, 255 Kit CHEMRAZ seal • Nut (Pos. 150) • CHEMRAZ O-ring, 2 pcs. (Pos. 255) 71086368 150, 250 Kit VITON seal • Nut (Pos. 150) • VITON O-ring, 3 pcs. (Pos. 250) 71086369 260 Kit PTFE sealing disk for DN 50 71086372 270 Kit PTFE sealing disk for ANSI 2" and JIS 10K 50A 71086374 150, 280 Kit fixed flange DN 50, stainless steel 1.4404 (AISI 316L) • Nut (Pos. 150) • Flange DN 50 (Pos. 280) 51500525 150, 285 Kit fixed flange ANSI 2", stainless steel 1.4404 (AISI 316L) • Nut (Pos. 150) • Flange ANSI 2" (Pos. 285) 51500527 150, 286 Kit fixed flange JIS, stainless steel 1.4404 (AISI 316 L)Nut • (Pos. 150) • Flange DN 50 (Pos. 286) 51500934 150, 288, 292 Kit lap-joint flange ANSI 2", PVDF • Nut (Pos. 150) • Flange ANSI 2", PVDF (Pos. 288) • Lap-joint flange, UP-GF (Pos. 292) 51500937 150, 287, 291 Kit lap-joint flange DN 50, PVDF • Nut (Pos. 150) • Flange DN 50, PVDF (Pos. 287) • Lap-joint flange, UP-GF (Pos. 291) 51500936 150, 289, 293 Kit lap-joint flange JIS, PVDF • Nut (Pos. 150) • Flange JIS, PVDF (Pos. 289) • Lap-joint flange, UP-GF (Pos. 293) 51500935 a0007081 a0007082 Endress+Hauser 19 Spare parts and return 7.2 Indumax CLS50/CLS50D Return The device must be returned if repairs or a factory calibration are required, or if the wrong device has been ordered or delivered. According to legal regulations, Endress+Hauser, as an ISO-certified company, is required to follow certain procedures when handling returned products that are in contact with medium. To ensure swift, safe and professional device returns, please read the return procedures and conditions on the internet site: www.services.endress.com/return-material 20 Endress+Hauser Indumax CLS50/CLS50D Technical data 8 Technical data 8.1 Input 8.1.1 Measured variable • Conductivity • Temperature 8.1.2 Cell constant k = 1.98 cm–1 8.1.3 Measuring frequency 2 kHz 8.1.4 Measuring ranges Conductivity: Temperature: 2 μS/cm to 2000 mS/cm (uncompensated) –20 to +180 ˚C (-4 to +350 ˚F) 8.1.5 Temperature measurement CLS50D Pt 1000 (class A acc. to IEC 60751) CLS50 Pt 100 (class A acc. to IEC 60751) 8.2 Performance characteristics 8.2.1 Maximum measured error • -20 to 100 ˚C (-4 to 212 ˚F): ±(5 μS/cm + 0.5 % of the measured value) • > 100 ˚C (212 ˚F): ±(10 μS/cm + 0.5 % of the measured value) 8.2.2 Temperature response time • PEEK versions: approx. 7 min • PFA versions: approx. 11 min Endress+Hauser 21 Technical data 8.3 Indumax CLS50/CLS50D Environment 8.3.1 Ambient temperature range CLS50D –10 to +60 ˚C (+10 to +140 ˚F) CLS50 –10 to +70 ˚C (+10 to +160 ˚F) 8.3.2 Storage temperature –20 to +80 ˚C (-4 to +180 ˚F) 8.3.3 Ingress protection IP 68 / NEMA 6 (installed with original sealing) 8.4 Process 8.4.1 Process temperature CLS50D Without flange DN50, ANSI 2" JIS PVDF lap-joint flange Sensor CLS50D-*1/2 CLS50D-*3/4/5/6/8 CLS50D-*7 CLS50D-*A/B/C PEEK –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) PFA –20 to 110 ˚C (-4 to 230 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) Without flange DN50, ANSI 2" JIS PVDF lap-joint flange Sensor CLS50-*1/2 CLS50-*3/4/5/6/8 CLS50-*7 CLS50-*A/B/C PEEK –20 to 180 ˚C (-4 to 360 ˚F) –20 to 180 ˚C (-4 to 360 ˚F) –20 to 180 ˚C (-4 to 360 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) PFA –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) –20 to 125 ˚C (-4 to 260 ˚F) CLS50 8.4.2 Process pressure max. 20 bar (290 psi), acc. to the sensor version, see pressure-temperature diagram 22 Endress+Hauser Indumax CLS50/CLS50D Technical data 8.4.3 Pressure-temperature diagram a0018311 Fig. 12: Pressure-temperature-diagram of CLS50D 1 2 3 4 5 PEEK sensor, without flange PFA sensor, without flange (blue line) PEEK or PFA sensor, with DN50/ANSI 2" flange (red line) PEEK or PFA sensor, with JIS flange PEEK or PFA sensor, with lap-joint flange PVDF (green line) a0018312 Fig. 13: Pressure-temperature-diagram of CLS50 1 2 3 4 5 6 PEEK sensor, without flange PFA sensor, without flange or with DN50/ANSI 2" flange (blue line) PEEK sensor, with DN50/ANSI 2" flange (red line) PFA sensor, with JIS flange (black line) PEEK or PFA sensor, with lap-joint flange PVDF (green line) PEEK sensor, with JIS flange (grey line) Endress+Hauser 23 Technical data 8.5 Indumax CLS50/CLS50D Mechanical construction 8.5.1 Weight approx. 650 g (1.43 lbs) 8.5.2 Material Sensor: Sensor seal: Process connections: G ¾: PEEK, PFA (depending on ordered version) VITON, CHEMRAZ (depending on ordered version) CLS50-**A: stainless steel 1.4571 (AISI 316Ti) CLS50-**B/C: PEEK GF30 CLS50D-**D: stainless steel 1.4571 (AISI 316Ti) CLS50D-**B/C: PEEK GF30 NPT 1": PEEK Fixed flange: stainless steel 1.4404 (AISI 316 L) Sealing disk: GYLON (ceramic-filled PTFE) Lap-joint flange: PP-GF Flange combined with lap-joint flange: PVDF 8.5.3 Chemical durability Medium Concentration PEEK PFA CHEMRAZ VITON Sodium hydroxide solution NaOH 0 to 50 % 20 to 100 ˚C (68 to 212 ˚F) not suitable 0 to 150 ˚C (32 to 302 ˚F) not suitable 0 to 10 % 20 to 100 ˚C (68 to 212 ˚F) 20 to 80 ˚C (68 to 176 ˚F) 0 to 150 ˚C (32 to 302 ˚F) 0 to 120 ˚C (32 to 248 ˚F) 0 to 40 % 20 ˚C (68 ˚F) 20 to 60 ˚C (68 to 140 ˚F) 0 to 150 ˚C (32 to 302 ˚F) 0 to 120 ˚C (32 to 248 ˚F) 0 to 80 % 20 to 100 ˚C (68 to 212 ˚F) 20 to 60 ˚C (68 to 140 ˚F) 0 to 150 ˚C (32 to 302 ˚F) 0 to 120 ˚C (32 to 248 ˚F) 0 to 2.5 % 20 to 80 ˚C (68 to 176 ˚F) 20 to 100 ˚C (68 to 212 ˚F) 0 to 150 ˚C (32 to 302 ˚F) 0 to 120 ˚C (32 to 248 ˚F) 0 to 30 % 20 ˚C (68 ˚F) 20 to 100 ˚C (68 to 212 ˚F) 0 to 150 ˚C (32 to 302 ˚F) 0 to 120 ˚C (32 to 248 ˚F) 0 to 5 % 20 to 100 ˚C (68 to 212 ˚F) 20 to 80 ˚C (68 to 176 ˚F) 0 to 150 ˚C (32 to 302 ˚F) 0 to 120 ˚C (32 to 248 ˚F) 0 to 10 % 20 to 100 ˚C (68 to 212 ˚F) 20 to 80 ˚C (68 to 176 ˚F) 0 to 150 ˚C (32 to 302 ˚F) 0 to 120 ˚C (32 to 248 ˚F) Nitric acid HNO3 Phosphoric acid H3PO4 Sulphuric acid H2SO4 Hydrochloric acid HCl No responsibility is taken for the correctness of this information. 24 Endress+Hauser Indumax CLS50/CLS50D 9 Appendix 9.1 Declaration of conformity for CLS50-G and CLS50D-BA Appendix a0007216 Endress+Hauser 25 Appendix Indumax CLS50/CLS50D a0014933 26 Endress+Hauser Indumax CLS50/CLS50D 9.2 Appendix Declaration of conformity for CLS50-V a0013271 Endress+Hauser 27 BA00182C/07/EN/15.12 FM9 / DT