Emerson Model 398R & 398RVP Retractable pH/ORP Sensors Instruction Manual

Instruction Manual PN 51-398R/rev.G January 2011 Model 398R & 398RVP Retractable pH/ORP Sensors MODEL 398R MODEL 398RVP (shown in ball valve) DANGER HAZARDOUS AREA INSTALLATION ESSENTIAL INSTRUCTIONS READ THIS PAGE BEFORE PROCEEDING! Rosemount Analytical designs, manufactures, and tests its products to meet many national and international standards. Because these instruments are sophisticated technical products, you must properly install, use, and maintain them to ensure they continue to operate within their normal specifications. The following instructions must be adhered to and integrated into your safety program when installing, using, and maintaining Rosemount Analytical products. Failure to follow the proper instructions may cause any one of the following situations to occur: Loss of life; personal injury; property damage; damage to this instrument; and warranty invalidation. • Read all instructions prior to installing, operating, and servicing the product. If this Instruction Manual is not the correct manual, telephone 1-800-654-7768 and the requested manual will be provided. Save this Instruction Manual for future reference. • If you do not understand any of the instructions, contact your Rosemount representative for clarification. • Follow all warnings, cautions, and instructions marked on and supplied with the product. • Inform and educate your personnel in the proper installation, operation, and maintenance of the product. • Install your equipment as specified in the Installation Instructions of the appropriate Instruction Manual and per applicable local and national codes. Connect all products to the proper electrical and pressure sources. • To ensure proper performance, use qualified personnel to install, operate, update, program, and maintain the product. • When replacement parts are required, ensure that qualified people use replacement parts specified by Rosemount. Unauthorized parts and procedures can affect the product’s performance and place the safe operation of your process at risk. Look alike substitutions may result in fire, electrical hazards, or improper operation. • Ensure that all equipment doors are closed and protective covers are in place, except while maintenance is being performed by qualified persons, to prevent electrical shock and personal injury. Installations near flammable liquids or in hazardous area locations must be carefully evaluated by qualified on site safety personnel. This sensor is not Intrinsically Safe or Explosion Proof. To secure and maintain an intrinsically safe installation, the certified safety barrier, transmitter, and sensor combination must be used. The installation system must comply with the governing approval agency (FM, CSA or BASEEFA/CENELEC) hazardous area classification requirements. Consult your analyzer/transmitter instruction manual for details. Proper installation, operation and servicing of this sensor in a Hazardous Area Installation is entirely the responsibility of the user. WARNING RETRACTABLE SENSORS Retractable sensors must not be inserted nor retracted when process pressures are in excess of 64 psig (542kPa), option 21 or 35 psig (343 kPa) option 25. CAUTION SENSOR/PROCESS APPLICATION COMPATIBILITY The wetted sensor materials may not be compatible with process composition and operating conditions. Application compatibility is entirely the responsibility of the user. ATEX DIRECTIVE Special Conditions for safe use 1. All pH/ORP sensors have a plastic enclosure which must only be cleaned with a damp cloth to avoid the danger due to a build up of an electrostatic charge. 2. All pH/ORP sensor Models are intended to be in contact with the process fluid and may not meet the 500V r.m.s. a.c. test to earth. This must be taken into consideration at installation. About This Document This manual contains instructions for installation and operation of the Models 398R and 398RVP TUpH Retractable pH/ORP Sensors. The following list provides notes concerning all revisions of this document. Rev. Level Date Notes 0 1/99 This is the initial release of the product manual. The manual has been reformatted to reflect the Emerson documentation style and updated to reflect any changes in the product offering. A 7/02 Updated multiple drawings. B 8/02 Added drawing #40105549, rev. D. C 10/02 Revised drawing on page 10. D 8/03 Added Silcore information. E 6/04 Added Xmt wiring drawings. F 10/05 Updated registration marks of Viton and Tefzel. G 1/11 Removed RAI patent references, added ATEX directive MODEL 398R/398RVP pH/ORP TABLE OF CONTENTS MODEL 398R/398RVP RETRACTABLE pH/ORP SENSOR TABLE OF CONTENTS Section 1.0 1.1 1.2 1.3 Title DESCRIPTION AND SPECIFICATIONS........................................................... Features and Applications................................................................................. Performance and Physical Specifications ......................................................... Ordering Information ......................................................................................... Page 1 1 3 3 2.0 2.1 2.2 INSTALLATION ................................................................................................. Unpacking and Inspection ................................................................................. Mechanical Installation ..................................................................................... 6 6 6 3.0 3.1 3.2 WIRING THE MODEL 398R SENSOR ............................................................. General ............................................................................................................. Wiring Diagrams................................................................................................ 13 13 13 4.0 4.1 4.2 WIRING THE MODEL 398RVP SENSOR......................................................... General ............................................................................................................. Wiring Diagrams................................................................................................ 28 28 28 5.0 5.1 5.2 5.3 5.4 5.5 START UP AND CALIBRATION........................................................................ General Information .......................................................................................... Use of Calibration Buffers ................................................................................. Two-point Buffer Calibration: General Instructions............................................ pH Standardization: General Instructions.......................................................... ORP Standardization: General Instructions....................................................... 36 36 36 37 37 37 6.0 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 MAINTENANCE ................................................................................................ Maintenance...................................................................................................... Sensor Removal................................................................................................ Cleaning Procedures - pH Sensors................................................................... Cleaning Procedures - ORP Sensors ............................................................... Checking the Reference Electrode ................................................................... Rejuvenating Reference Electrodes.................................................................. Temperature Element........................................................................................ Sensor Tube Replacement When Used With a Sensor-mounted Junction Box. 38 38 38 39 40 40 41 41 41 7.0 TROUBLESHOOTING ...................................................................................... 43 8.0 RETURN OF MATERIAL................................................................................... 46 i MODEL 398R/398RVP pH/ORP TABLE OF CONTENTS MODEL 398R/398RVP RETRACTABLE pH/ORP SENSOR LIST OF FIGURES Figure No. Title Page 1-1 Cross Section Diagram of the TUpH Reference Technology ............................ 2 2-1 Exploded View of Ball Valve Kit PN 23240-00 used with process connector ... PN 23166-00 (or PN 23166-01) ......................................................................... 7 2-2 Exploded View of Ball Valve Kit PN 23765-00 .................................................. 7 2-3 Typical Mounting Details-Retraction Version..................................................... 8 2-4 Dimensional Warning Label and Sensor Diagram ............................................ 9 2-5 Dimensional Drawing for Ball Valve Kit PN 23465-00 ....................................... 10 2-6 Dimensional Drawing for Ball Valve Kit PN 23240-00 ....................................... 11 2-7 Dimensional Drawing of Model 398R shown with Sensor Head Junction Box, with and without 1-1/2 in. Ball Valve PN 23240-00 .......................................... 12 3-1 Wire Configurations........................................................................................... 14 3-2 Wiring Details for Sensor Model 398R-54-62 to Analyzer Model 54 ................. 14 3-3 Wiring Sensor Model 398R-54-62 to Analyzer Model 1055-01-10-22-32 ......... 14 3-4 Wiring Details for Sensor Model 398R-54-62 Through Remote Junction Box . PN 23555-00 or Through Sensor-Mounted Junction Box PN 23709-00 to ..... Analyzer Model 54..................................................................................................... 15 3-5 Wiring Model 398R-54-61/62 to Model 1055-22-32 thru Remote Junction Box .. 15 3-6 Wiring Details for Sensor Model 398R-54-62 to Analyzer/Transmitter Model 81 16 3-7 Wiring Details for Sensor Model 398R-54-62 Through Remote Junction Box . PN 23555-00 or Model 398R-54-61 Through Sensor-Mounted Junction Box . PN 23709-00 to Analyzer Model 81 .................................................................. 16 3-8 Wiring Details for Sensor Model 398R-54-62 to Analyzer/Transmitter Model 3081 17 3-9 Wiring Details for Sensor Model 398R-54-62 Through Remote Junction Box . PN 23555-00 or Model 398R-54-61 Through Sensor-Mounted Junction Box PN 23709-00 to Analyzer Model 3081 .............................................................. 17 Wiring Details for Sensor Model 398R-50-62 or 398R-54-62 to Transmitter ... Model 1181........................................................................................................ 18 Wiring Details for Sensor Model 398R-50 Through Remote Junction Box ...... PN 23309-03 to Transmitter Model 1181 ......................................................... 18 Wiring Details for Sensor Model 398R-50-60 Through Sensor-Mounted ......... Junction Box PN 23707-00 to Transmitter Model 1181 ..................................... 19 3-10 3-11 3-12 3-13 and 2054 Wiring Details for Sensor Model 398R-54 to Analyzer Models 1054A, 1054B, ......................................................................................................................19 3-14 Wiring Details for Sensor Model 398R-54 Through Remote Junction Box ...... PN 23309-03 to Analyzer Models 1054A, 1054B, and 2054 ............................ 20 Wiring Details for Sensor Model 398R-54-60 Through Sensor-Mounted ......... Junction Box PN 23708-01 to Analyzer Models 1054A, 1054B, and 2054 ....... 20 3-16 Wiring Details for Sensor Model 398R-54-62 to Transmitter Model 2081......... 21 3-17 Wiring Details for Sensor Model 398R-54 Through Remote Junction Box ...... PN 23309-03 to Transmitter Model 2081 .......................................................... 21 Wiring Details for Sensor Model 398R-54-60 Through Sensor-Mounted ........ Junction Box PN 23708-01 to Transmitter Model 2081 .................................... 22 3-15 3-18 ii MODEL 398R/398RVP pH/ORP TABLE OF CONTENTS MODEL 398R/398RVP RETRACTABLE pH/ORP SENSOR LIST OF FIGURES (CONTINUED) Figure No. Title Page 3-19 Wiring Details for Sensor Model 398R-54-62 to Analyzer Model 1054 ............ 22 3-20 Wiring Details for Sensor Model 398R-54 Through Remote Junction Box ..... PN 23309-03 to Analyzer Model 1054 .............................................................. 23 Wiring Details for Sensor Model 398R-54-60 Through Remote Junction Box PN 23708-01 to Analyzer Model 1054 .............................................................. 23 3-22 Wiring Details for Sensor Model 398R-54-62 to Analyzer Model 2700 ............ 24 3-23 Wiring Details for Sensor Model 398R-54-62 to Analyzer Model SoluComp ... 24 3-24 BNC Preparation Instructions ........................................................................... 25 3-25 Extension Cable Preparation .............................................................................. 26 3-26 Wiring Model 398R-54-61 to Model Xmt-P-HT-10 ............................................. 27 3-27 Wiring Model 398R-54-62 to Model Xmt-P-HT-10 ............................................. 27 4-1 Wire Configurations for Variopol Cable PN 23645-06 and PN 23645-07 ......... 29 4-2 Wiring Details for Sensor Model 398RVP to Analyzer Model 54 and 54e ........ 29 4-3 Wiring Details for Sensor Model 398RVP to Analyzer Model 81 ...................... 29 4-4 Wiring Details for Sensor Model 398RVP to Analyzer Models 3081 & 4081.... 30 4-5 Wiring Details for Sensor Model 398RVP to Analyzer Model 2081 .................. 30 4-6 Wiring Details for Sensor Model 398RVP to Analyzer Model 2700 .................. 30 4-7 Wiring Details for Sensor Model 398RVP to Analyzer Model 1054 .................. 31 4-8 Wiring Details for Sensor Model 398RVP to Analyzer Models 1054A/B and ... 2054 ..................................................................................................................... 31 Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN ........ 23309-03 to Analyzer Models 1181, 1060, 1003, and 1023 .............................. 31 Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN ........ 23309-04 to Analyzer Models 1054A/B and 2054 ............................................. 31 4-11 Wiring Details for Sensor Model 398RVP to Analyzer Model 1181 ................... 32 4-12 Wiring Details for Sensor Model 398RVP to Analyzer Model SCL-(P/Q) ......... 32 4-13 Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN ........ 23309-03 to Analyzer Model 2081 ...................................................................... 32 Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN ........ 23309-04 to Analyzer Model 1054 ...................................................................... 32 Wiring Details for Sensor Model 398RVP thru Remote Junction Box to ......... Analyzer Model 54............................................................................................... 33 Wiring Details for Sensor Model 398RVP thru Remote Junction Box to ......... Analyzer Model 81............................................................................................... 33 Wiring Details for Sensor Model 398RVP thru Remote Junction Box to ......... Analyzer Model 3081 and 4081 .......................................................................... 33 4-18 Extension Cable Preparation .............................................................................. 34 4-19 Wiring Model 398RVP to Model 1055-22-32...................................................... 35 4-20 Wiring Model 398RVP to Model Xmt-P-HT-10 ................................................... 35 3-21 4-9 4-10 4-14 4-15 4-16 4-17 iii MODEL 398R/398RVP pH/ORP TABLE OF CONTENTS MODEL 398R/398RVP RETRACTABLE pH/ORP SENSOR LIST OF FIGURES (CONTINUED) Figure No. Title Page 6-1 Sensor Tube Replacement ............................................................................... 38 6-2 Model 398R pH Sensor..................................................................................... 40 6-3 Checking the Potential of the Reference Electrode.......................................... 40 6-4 Three-Wire RTD Circuit..................................................................................... 41 6-5 Male Connector Tightening Diagram ................................................................ 42 LIST OF TABLES Table No. Title Page 1-1 Commonly Used Accessories ........................................................................... 4 1-2 Other Accessories ............................................................................................. 5 3-1 Wiring Guide ..................................................................................................... 13 4-1 Wiring Guide ..................................................................................................... 28 6-1 Resistance as a Function of Temperature for Selected RTDs.......................... 41 7-1 Troubleshooting ............................................................................................... 43 iv MODEL 398R/398RVP pH/ORP SECTION 1.0 DESCRIPTION AND SPECIFICATIONS SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.1 FEATURES AND APPLICATIONS The chemical-resistant construction of Tefzel® 1, titanium, and the TUpH reference junction makes the Model 398R and 398RVP the ideal sensors for measuring pH in harsh process liquids. Use these sensors to measure pH in sour water strippers, in pulp bleaching towers that use chlorine dioxide, and in process streams containing a variety of organic solvents. The TUpH reference technology provides maximum life and ensures low maintenance in processes that typically coat reference junctions. Standard porous junctions plug easily, leading to noisy, drifting pH readings and increased maintenance. The TUpH junction fights plugging in two ways. TUpH junction pores are much smaller than the smallest particles likely to be in the process. Therefore, particles do not block the pores but remain on the surface. The junction surface area is large, so many solids can accumulate on the junction before the pH signal degrades. TUpH sensors also resist poisoning. The long internal helical diffusion pathway hinders poisoning agents, like sulfide, mercury, cyanide, and ammonia, from migrating into the reference electrode. The entire line of TUpH model sensors now incorporate the new SILCORE™2 technology contaminant barrier. This triple-seal barrier prevents moisture and material impurities from migrating to the pH sensor’s reference electrode’s metal lead wire. By preventing these contaminants from compromising the integrity of the pH measurement, sensor life is increased, especially at higher temperatures where increased migrations occur. In addition, the SILCORE technology provides added protection against sensor failure due to vibrations and shock by transferring damaging energy away from the glass-to-metal seal. The ACCUGLASS™2 pH bulb means the glass electrode resists cracking and has nearly theoretically perfect response even at extreme pH values. A slotted tip surrounding the glass bulb provides additional protection against breakage. The sensor can be oriented with the bulb directly in the stream, or it can be turned ninety degrees, permitting the shroud to protect the glass bulb from particles. The Model 398R and 398RVP use the highest quality materials to provide superior chemical resistance. These retractable sensors are housed in a titanium tube and are designed for use with a 1-1/4 inch or 1-1/2 inch ball valve. The molded Tefzel® 1 TUpH construction is offered with a choice of seals (Viton® 1 or Kalrez® 1). Combining high quality materials with the TUpH reference technology and ACCUGLASS™ pH bulb allows for ultimate chemical resistance and makes the Model 398R the perfect choice for measuring pH in harsh, demanding processes. The 398R is available with 15 ft. of cable for wiring directly to an analyzer/transmitter or a remote junction box. The sensor is also available with 9.5 in. of cable for use with a sensor head junction box which attaches to the sensor tube using a compression fitting. Due to the high impedance pH signal, a preamplifier must be used and can be housed in the analyzer/ transmitter or junction box. The 398RVP is available with a six-pin connector and uses a mating connector cable. The Models 398Rand 398RVP are compatible with all Rosemount Analytical and various other manufacturers instruments. 1 Tefzel, Kalrez and Viton are registered trademarks of DuPont Performance Elastomers. 2 ACCUGLASS and Silcore are trademarks of Rosemount Analytical. 1 MODEL 398R/398RVP pH/ORP SECTION 1.0 DESCRIPTION AND SPECIFICATIONS Cross Section Diagram of the TUpH Reference Technology All TUpH sensors are designed with a large area reference junction, helical reference pathway, and an AccuGlass pH glass bulb. This sensor technology ensures superior performance while only requiring minimal maintenance. 2 MODEL 398R/398RVP pH/ORP SECTION 1.0 DESCRIPTION AND SPECIFICATIONS 1.2 PERFORMANCE AND PHYSICAL SPECIFICATIONS Measured Range: ORP: -1500 to 1500mV pH: GPHT ACCUGLASS, 0 - 14 pH Percent Linearity Over pH Ranges: pH range 0-2 pH 2-12 pH 12-13 pH 13-14 pH Hemi Bulb 94% 99% 97% 92% Reference: Permeable Tefzel with secondary helical pathway Wetted Materials: Titanium, Tefzel 1, glass, platinum (ORP only), and choice of Viton 1 or Kalrez 1 ® ® ® Process Connections: With ball valve: 1-1/2 in. Without ball valve: 1 in. Cable: Standard integral 15 ft , optional 9.5 in.; Recommended Interconnect; PN 9200273 Maximum Process Pressure and Temperature: Hemi bulb: 250 psig (1825 kPa abs) at 212°F (100°C) Flat bulb: 100 psig (790 kPa abs) at 212°F (100°C) Maximum Pressure at Retraction or Insertion: 64 psig (524 kPa abs) Code 21 35 psig (343 kPa abs) Code 25 Minimum Conductivity: 75 µS/cm, nominal 100 µS/cm Weight/Shipping Weight: Sensor: Code 21; 2.0 lb/3.0 lb (.9kg/1.40kg) Code 25; 3.0 lb/4.0 lb (1.40 kg/1.80kg) 1.3 ORDERING INFORMATION The Model 398R and 398RVP Sensors, housed in a titanium tube and made with a patented Tefzel reference junction, can be used with a ball valve (order separately) for hot tap applications. The sensor is available with a hemi bulb glass pH electrode or a platinum and glass ORP electrode and with Pt100 or 3K temperature compensation. The 398R is provided with a standard 15 ft cable and is offered with an optional 9.5 in. cable for easy wiring to sensor head junction boxes. Model 398RVP is available with a six-pin VP connector and uses a mating connector cable (purchased separately). A preamplifier must be used if the sensor is more than 15 ft from the analyzer/transmitter. Junction box kits with preamplifiers must be ordered separately. Process connector and ball valve assemblies must also be ordered separately. MODEL 398R & 398RVP* TUpH RETRACTABLE pH SENSOR CODE MEASURING ELECTRODE TYPE (Required Selection) 10 GPHT hemi glass, General Purpose High Temperature (0-14 pH) 12 ORP 13 GPHT flat glass, General Purpose High Temperature (0-14 pH) CODE 21 25 SENSOR LENGTH (Required Selection) 21 in. Titanium Tube 36 in. Titanium Tube CODE 30 31 32 O-RING MATERIAL (Required Selection) EPDM Viton®1 Kalrez®1 (recommended for applications with Chlorine Dioxide) CODE 50 54 ANALYZER/TC COMPATIBILITY (Required Selection) For Models 1181 (3K TC) [no T.C. if ordered with option -12 (ORP)] For Models 1054, 1054A/B, 2054, 2081,54, 3081, 81, SCL-(P/Q), Solu Cube (PT 100 RTD) CODE 60 61 62 OPTIONAL SELECTIONS (not valid with Model 398RVP) 9.5 in. cable with BNC (use with Model 1181, 1054 series, 2054, 2081 sensor-head junction boxes) 9.5 in. cable no BNC (not valid w/option -50) (use with Model 54, 81, 3081 sensor-head junction boxes) 15 ft cable, no BNC (not valid w/option -50), wire directly to Model 54, 81, 3081 transmitter/analyzers 398R - 10 - 21 - 32 - 54 EXAMPLE * Cable should be ordered separately for first time installations of Model 398RVP. 1 Tefzel and Viton are registered trademarks of DuPont Performance Elastomers. 3 MODEL 398R/398RVP pH/ORP SECTION 1.0 DESCRIPTION AND SPECIFICATIONS TABLE 1-1. Commonly Used Accessories For first time installations, Rosemount Analytical recommends using the following guide: ACCESSORIES WEIGHT/ SHIPPING WEIGHT 1. Variopol Mating Connector Cables (required only for Model 398RVP) Choose one: PN 23645-06, 15 ft. cable with mating VP connector, prepped with BNC on analyzer end 0.1 lb/ft (0.05 kg/ft)/1.1 lb/ft (0.6 kg/ft) PN 23645-07, 15 ft. cable with mating VP connector, prepped without BNC on analyzer end* 0.1 lb/ft (0.05 kg/ft)/1.1 lb/ft (0.6 kg/ft) 2. Retractable Mounting A. Choose one (required for all first time installations without ball valves or with 1-1/2 in. ball valve): PN 23166-00, 1 in. MNPT process connector, Stainless Steel w/EPDM O-ring 0.5 lb (0.3 kg)/1.5 lb (0.8 kg) PN 23166-01, 1 in. NPT process connector, Titanium w/EPDM O-ring 0.5 lb (0.3 kg)/1.5 lb (0.8 kg) B. Choose one (Optional; Process Connector O-rings): PN 9550220, O-ring, Kalrez®1, 2-214 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) PN 9550099, O-ring, Viton 1, 2-214 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) ® C. Choose one: PN 23240-00, 1-1/2 in. ball valve assembly, 316 SST (process connector required) 6.0 lb (3.0 kg)/7.0 lb (3.5 kg) PN 23765-00, 1-1/4 in. ball valve assembly, 316 SST, with graphite packed adapter 6.0 lb (3.0 kg)/7.0 lb (3.5 kg) 3. Junction Boxes (Optional; Choose either Sensor Head or Remote) A. Sensor Head Junction Boxes (used with 9.5 in. cable length sensor) Choose one: PN 23709-00; includes preamplifier for Models 54, 81, 1055, 3081, 4081 3.3 lb (1.5 kg)/4.3 lb (2.0 kg) PN 23708-01; includes preamplifier for Models 1054 series, 2054, 2081 3.3 lb (1.5 kg)/4.3 lb (2.0 kg) PN 23707-00; includes preamplifier for Model 1181 3.3 lb (1.5 kg)/4.3 lb (2.0 kg) B. Remote Junction Boxes (used with 15 ft cable length sensor or Model 398RVP) Choose one: PN 23555-00; includes preamplifier for Models 54, 81, 1055, 3081, 4081 1.3 lb (0.6 kg)/2.3 lb (1.1 kg) PN 23309-03; includes preamplifier for Model 1181 1.3 lb (0.6 kg)/2.3 lb (1.1 kg) PN 23309-04; includes preamplifier for Models 1054 series, 2054, 2081 1.3 lb (0.6 kg)/2.3 lb (1.1 kg) PN 23054-03; includes preamplifier for SoluCube Model 2700 3.1 lb (1.4 kg)/4.1 lb (1.9 kg) 4. Wiring Configuration for Model 398R only (no option needed with remote junction boxes PN 23309-03, PN 23309-04, and PN 23555-00): Choose one: Order option -60 (standard with BNC connector) for PN 23707-00 or 23708-01 sensor head junction boxes Order option -61 (no BNC) for PN 23709-00 sensor head junction box Order option -62 (no BNC) for PN 23550-00 and 23054-03 remote junction boxes 5. Extension Cables - Choose one: PN 23646-01, 11 conductor, shielded, prepped 0.1 lb/ft (0.05 kg/ft)/1.1 lb/ft (0.6 kg/ft) PN 9200273, 11 conductor, shielded, unprepped 0.1 lb/ft (0.05 kg/ft)/1.1 lb/ft (0.6 kg/ft) PN 9200254, for extension cables from Remote Junction Box 23309-04 to Models 1054 series, 2054, and 2081 0.1 lb/ft (0.05 kg/ft)/1.1 lb/ft (0.6 kg/ft) * Used for connections to Models 1181, 1054, 2081, 54, 81, 3081, 4081, and remote junction box PN 23555-00. 1 Tefzel and Viton are registered trademarks of DuPont Performance Elastomers. 4 MODEL 398R/398RVP pH/ORP SECTION 1.0 DESCRIPTION AND SPECIFICATIONS TABLE 1-2. OTHER ACCESSORIES PART DESCRIPTION WEIGHT/SHIPPING WEIGHT 22698-00 Preamplifier plug-in for remote junction box (PN 23309-03), for Model 1003 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 22698-02 Preamplifier plug-in for remote junction box (PN 23309-03), for Models 1181/1050 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 22698-03 Preamplifier plug-in for remote junction box (PN 23309-04), for Models 1054A/B, 2054, 2081 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 22743-01 Pt100 Preamplifier for Model 1181 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 22744-01 3K Preamplifier for Model 1181 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 23557-00 Preamplifier for remote junction box (PN 23555-00), for Models 54/3081/81 0.2 lb (0.1 kg)/1.2 lb (0.6 kg) 23550-00 Remote Junction box with extension board 3.3 lb (1.5 kg)/4.3 lb (2.0 kg) 9550167 O-ring, 2-214, EPDM for process connector 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 9550099 ® 1 O-ring, Viton , for process connector ® 1 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 9550220 O-ring, Kalrez , for process connector 0.1 lb (0.05 kg)/1.1 lb (0.6 kg) 9210012 Buffer solution, 4.01 pH, 16 oz 1.2 lb (0.5 kg)/2.2 lb (1.0 kg) 9210013 Buffer solution, 6.86 pH, 16 oz 1.2 lb (0.5 kg)/2.2 lb (1.0 kg) 9210014 Buffer solution, 9.18 pH, 16 oz 1.2 lb (0.5 kg)/2.2 lb (1.0 kg) 1 Viton and Kalrez are registered trademarks of DuPont Performance Elastomers. 5 MODEL 398R/398RVP pH/ORP SECTION 2.0 INSTALLATION SECTION 2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION. Inspect the outside of the carton for any damage. If damage is detected, contact the carrier immediately. Inspect the instrument and hardware. Make sure all items in the packing list are present and in good condition. Notify the factory if any part is missing. NOTE If the sensor is to be stored, the protective boot should be filled with either KCl electrolyte solution or pH 4.0 buffer solution and replaced on sensor tip until ready to use. 2.2.1 INSTALLATION THROUGH BALL VALVE. 1. Carefully remove the liquid filled rubber boot which protects the glass electrode and keeps the liquid junction wet during shipping and storage. Discard the liquid and boot. Make sure the lubricated Oring is in place in the groove inside the male connector on the sensor body (Figure 6-1). NOTE Save the original packing cartons and materials as most carriers require proof of damage due to mishandling, etc. Also, if it is necessary to return the instrument to the factory, you must pack the instrument in the same manner as it was received. Refer to Section 6.0 for instructions. 2. With the male connector on the sensor’s body, insert the sensor into the ball valve until it gently touches the closed valve. The molded electrode guard will protect the glass bulb from breakage (extra caution should be taken when inserting the flat glass sensor into the valve because it does not have an electrode guard). 3. Thread the male connector body tightly into the ball valve assembly. DO NOT tighten the hex nut on the male connector body; doing so would not allow the sensor to be inserted through the ball valve. 4. Pull back hard on the sensor assembly, as if trying to remove the sensor, to be certain that the sensor cannot come free of the ball valve assembly. The built-in retraction stop will butt against the shoulder of the male connector if properly installed. WARNING Glass electrode must be wetted at all times (in storage and in line) to maximize sensor life. 2.2 MECHANICAL INSTALLATION. Both models may be installed through a weldalet or in a pipe tee or “Y”, as shown in Figure 2-2, when used with a ball valve. Insert the end of the sensor to a depth sufficient to ensure that the glass bulb is continuously wetted by the process fluid. Each model can also be inserted directly into the process without the use of a ball valve for applications not requiring continuous operation during sensor maintenance. CAUTION Allow sufficient room for safe retraction and insertion of the sensor. Personnel should have room for stable footing while performing removal or insertion of the sensor. The sensor must be mounted within 10-90 degrees of the horizontal with the tip pointed downward. This ensures that the inside surface of the pH-sensitive glass bulb is completely wetted and that there is a good electrical connection between the bulb and the internal silver/silver chloride reference electrode. If the retraction version is to be installed without a ball valve follow the installation procedure for insertion service (Section 2.2.2). Perform the following steps for sensor installation through a ball valve: 6 CAUTION Buffer solution, in the protective boot, may cause skin or eye irritation. CAUTION The sensor must be captured by the valve assembly and the male connector so that it cannot be blown free by process pressure if mishandled during insertion or retraction. 5. After confirming that the sensor assembly is properly secured by the valve assembly, the valve may be opened and the sensor positioned into the process at the desired depth and orientation. 6. While holding the sensor in position, tighten the hex nut of the male connector to firmly secure the sensor in place. When the hex nut is tightened, the Teflon ferrule inside the compression fitting clamps the sensor tube (see Figure 6-2). CAUTION Over tightening the hex nut may damage the ferrule. NOTE A stainless steel ferrule is available if the Teflon ferrule does not adequately grip. When using the metallic ferrule, care must be taken to avoid over tightening and damaging the sensor tube. If the male connector leaks during insertion or retraction, replace the O-ring in the male connector (see Figure 6-1). MODEL 398R/398RVP pH/ORP SECTION 2.0 INSTALLATION 398R PN 9310102 BALL VALVE KIT FIGURE 2-1. Exploded View of Ball Valve Kit PN 23240-00 used with process connector PN 23166-00 (or PN 23166-01) [Ball Valve Kit includes 1-1/2 in. x 1 in. reducer, 1-1/2 in. close nipple, and 1-1/2 in. ball valve] FIGURE 2-2. Exploded View of Ball Valve Kit PN 23765-00 7 MODEL 398R/398RVP pH/ORP SECTION 2.0 INSTALLATION 2.2.2 INSTALLATION WITHOUT A BALL VALVE. Models 398R and 398RVP Sensors may be installed through a weldalet or pipe tee or “Y” when used with a process connector (PN 23166-00 or 23166-01). The sensor should be installed within 80° of vertical, with the electrode facing down. SENSOR HEAD JUNCTION BOX IS OPTIONAL FIGURE 2-3. Typical Mounting Details-Retraction Version Note: Sensor must be mounted at an angle between 10° and 90° above the horizontal. Pipe tees and weldalets provided by customer. Only Model 398R should be used with a sensor head junction box. 8 MODEL 398R/398RVP pH/ORP SECTION 2.0 INSTALLATION MILLIMETER INCH 4.920 2.25 Front Side 398R-21 Note: Retraction and max. operating pressure for 21 in. tube with flat glass is shown on this label. Retraction and max. operating pressure for the 21 in. and the 36 in. sensors are shown in the tables below. Back Side 398R A MM / IN 548.64 / 21.60 916.94 / 36.10 Sensor Tube Length 21 inches 36 inches Retraction Pressure 64 psig (542 kPa) 35 psig (343 kPa) MAXIMUM OPERATING PRESSURE Flat bulb — 100 psig Hemi bulb — 250 psig FIGURE 2-4. Dimensional Warning Label and Sensor Diagram Note: For Model 398RVP, the overall dimensional length increases by 1.9 inches (48 mm). 9 MODEL 398R/398RVP pH/ORP SECTION 2.0 INSTALLATION WHEN INCH AND METRIC DIMS ARE GIVEN MILLIMETER INCH DWG. NO. 4396RVP34 REV. B FIGURE 2-5. Dimensional Drawing for Ball Valve Kit PN 23765-00 (shown with Model 398RVP) 10 MODEL 398R/398RVP pH/ORP SECTION 2.0 INSTALLATION WHEN INCH AND METRIC DIMS ARE GIVEN MILLIMETER INCH DWG. NO. 40398R03 Ball Valve Kit (PN 23240-00) REV. A A process connector (PN 23166-00 or -01) must be used to connect the sensor to Ball Valve Kit 23240-00. Process connector can be purchased separately. FIGURE 2-6. Dimensional Drawing for Ball Valve Kit PN 23240-00 (shown with Model 398R). Note: For Model 398RVP, the overall dimensional length increases by 1.9 inches (48 mm) 11 MODEL 398R/398RVP pH/ORP SECTION 2.0 INSTALLATION WHEN INCH AND METRIC DIMS ARE GIVEN MILLIMETER INCH DWG. NO. 40396R03 REV. G FIGURE 2-7. Dimensional Drawing of Model 398R shown with Sensor Head Junction Box, with and without 1-1/2 in. Ball Valve PN 23240-00 Note: For the installations shown, the 1 in. x 1 in. process connector (PN 23166-00 or 23166-01), sensor head junction boxes (various part numbers; see page 3), and ball valve kit (PN 23240-00) must be purchased separately. Note: Sensor head junction boxes should be used with Model 396R options -60 or -61 only. 12 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR SECTION 3.0 WIRING THE MODEL 398R SENSOR 3.1 GENERAL Make electrical connections, as shown in Figures 3-1 through 3-25, using the following guidelines: 1. Pay particular attention to the analyzer or transmitter model number when following details on the wiring diagrams to ensure that the connections are made to the proper terminals. 2. Use Rosemount custom cable PN 9200273 (unprepped), 236446-01 (prepped), or PN 9200254 (unprepped) to connect the transmitter or analyzer to remote or sensor-mounted junction boxes. 3. The maximum distance from the sensor to the analyzer is 15 ft without an integral sensor preamplifier. NOTE For maximum EMI/RFI protection when wiring from the sensor to the junction box, the outer braid of the sensor should be connected to the outer braid of the extension cable. The outer braid of the extension cable to the instrument must be terminated at earth ground or by using an appropriate metal cable gland fitting that provides a secure connection tot he instrument cable. 3.2 WIRING DIAGRAMS. For wiring diagram information, refer to Table 3-1. 4. Run signal cable in a dedicated conduit away from AC power lines. TABLE 3-1. Wiring Guide for Model 398R Sensor SENSOR 398R-54-62 398R-54-62 398R-54-62 398R-54-62 398R-54-62 398R-54-62 398R-54 398R-50 or -54-62 398R-54-62 398R-54-62 SENSOR 398R-50 398R-54 398R-54 398R-54 398R-54-62 398R-54-62 398R-54-62 398R-54-62 SENSOR 398R-50-60 398R-54-60 398R-54-60 398R-54-60 398R-54-61 398R-54-61 398R-54-61 ANALYZER/TRANSMITTER 54 81 3081, 4081 2700 2081 1054 1054A, 1054B, 2054 1181 SoluComp Solu Comp II (1055) ANALYZER/TRANSMITTER 1181, 1050, 1060, 1003, 1023 1054A, 1054B, 2054 2081 1054 54 81 3081 Solu Comp II (1055) ANALYZER/TRANSMITTER 1181, 1050, 1060, 1003, 1023 1054A, 1054B, 2054 1054 2081 54 81 3081, 4081 REMOTE JUNCTION BOX 23309-03 23309-03 23309-04 23309-04 23555-00 23555-00 23555-00 23555-00 SENSOR-MOUNTED JUNCTION BOX 23707-00 23708-01 23708-01 23708-01 23709-00 23709-00 23709-00 FIGURE # 3-2 3-6 3-8 3-22 3-16 3-18 3-13 3-10 3-23 3-3 FIGURE # 3-11 3-13 3-17 3-20 3-4 3-7 3-9 3-5 FIGURE # 3-12 3-15 3-21 3-18 3-4 3-7 3-9 13 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR Wire Configuration for Code -60 and Standard Cable Options DWG. NO. REV. 40308139 A DWG. NO. 40005428 14 REV. A Wire Configuration for Code -61 and -62 Cable Options FIGURE 3-2. Wiring Details for Sensor Model 398R-54-62 to Analyzer Models 54 & 54e. FIGURE 3-1. Wire Configurations Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare the BNC as shown in Figure 3-22. FIGURE 3-3. Wiring Model 398R-( )-54-62 to Model 1055-01-10-22-32 MODEL 398R/398RVP pH/ORP NOTES: 1. PLACE 54pH/ORP LOCATION SWITCH TO SENSOR JUNCTION BOX POSITION. 2. SEE FIGURE [28] FOR PREPARATION INSTRUCTIONS FOR CABLE PN 9200273. 3. JUMPER BETWEEN TB1-7 AND TB1-8 SUPPLIED BY CUSTOMER. 4. ADDITIONAL CABLE PREP REQUIRED FOR MODEL 398R-54. SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40005427 REV. A FIGURE 3-4. Wiring Details for Sensor Model 398R-54-62 Through Remote Junction Box PN 23555-00 or Through Sensor-Mounted Junction Box PN 23709-00 to Analyzer Models 54 & 54e. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare the BNC as shown in Figure 3-22. For preparing wires on end of extension cable, use Figure 3-23. FIGURE 3-5. Wiring Model 398R-54-61/62 to Model 1055-22-32 through a Remote Junction Box 15 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40008126 REV. A FIGURE 3-6. Wiring Details for Sensor Model 398R-54-62 to Analyzer/Transmitter Model 81. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare the BNC as shown in Figure 3-22. DWG. NO. 40008124 REV. A FIGURE 3-7. Wiring Details for Sensor Model 398R-54-62 Through Remote Junction Box PN 23555-00 or Model 398R-54-61 Through Sensor-Mounted Junction Box PN 23709-00 to Analyzer Model 81. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare the BNC as shown in Figure 3-22. For preparing wires on end of extension cable, use Figure 3-23. 16 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 45081P12 REV. A FIGURE 3-8. Wiring Details for Sensor Model 398R-54-62 to Analyzer/Transmitter Models 3081, 4081, & 5081. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare the BNC as shown in Figure 3-22. DWG. NO. 45081P19 REV. A FIGURE 3-9. Wiring Details for Sensor Model 398R-54-62 Through Remote Junction Box PN 23555-00 or Model 398R-54-61 Through Sensor-Mounted Junction Box PN 23709-00 to Analyzer Models 3081, 4081, and 5081. Note: Sensor Model 398R-54 or 398R-54-60 can also be wired as shown above, but customer must prepare the BNC as shown in Figure 3-22. For preparing wires on end of extension cable, use Figure 3-23. 17 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40118163 REV. A FIGURE 3-10. Wiring Details for Sensor Model 398R-50-62 or 398R-54-62 to Transmitter Model 1181. Note: Sensor Model 398R-50 or 398R-54 can also be wired as shown above, but customer must prepare BNC as shown in Figure 3-22. DWG. NO. 40039706 REV. B FIGURE 3-11. Wiring Details for Sensor Model 398R-50 Through Remote Junction Box PN 23309-03 to Transmitter Model 1181 (also for Models 1050, 1060, 1003, and 1023) 18 MODEL 398R/398RVP pH/ORP DWG. NO. 40398R02 SECTION 3.0 WIRING THE MODEL 398R SENSOR REV. A FIGURE 3-12. Wiring Details for Sensor Model 398R-50-60 Through Sensor-Mounted Junction Box PN 23707-00 to Transmitter Model 1181 (also for Model s 1050, 1060, 1003, 1023). DWG. NO. 41054A35 REV. A FIGURE 3-13. Wiring Details for Sensor Model 398R-54 to Analyzer Models 1054A, 1054B, and 2054. 19 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 41054A36 REV. A FIGURE 3-14. Wiring Details for Sensor Model 398R-54 Through Remote Junction Box 23309-03 to Analyzer Models 1054A, 1054B, and 2054. DWG. NO. 41054A37 REV. A FIGURE 3-15. Wiring Details for Sensor Model 398R-54-60 Through Sensor-Mounted Junction Box PN 23708-01 to Analyzer Models 1054A, 1054B, and 2054. 20 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40208121 REV. A FIGURE 3-16. Wiring Details for Sensor Model 398R-54-62 to Transmitter Model 2081. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare BNC as shown in Figure 3-22. DWG. NO. 40208122 REV. A FIGURE 3-17. Wiring Details for Sensor Model 398R-54 Through Remote Junction Box PN 23309-04 to Transmitter Model 2081. 21 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40208123 REV. A FIGURE 3-18. Wiring Details for Sensor Model 398R-54-60 Through Sensor-Mounted Junction Box PN 23708-01 to Transmitter Model 2081. DWG. NO. 40105470 FIGURE 3-19. Wiring Details for Sensor Model 398R-54-62 to Analyzer Model 1054. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare BNC as shown in Figure 3-22. 22 REV. A MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40105471 REV. A FIGURE 3-20. Wiring Details for Sensor Model 398R-54 Through Remote Junction Box PN 23309-04 to Analyzer Model 1054. DWG. NO. 40105472 REV. A FIGURE 3-21. Wiring Details for Sensor Model 398R-54-60 Through Remote Junction Box PN 23708-01 to Analyzer Model 1054. 23 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. REV. 40039707 FIGURE 3-22. Wiring Details for Sensor Model 398R-54-62 to Analyzer Model 2700. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare BNC as shown in Figure 3-22. DWG. NO. 40398R01 REV. A FIGURE 3-23. Wiring Details for Sensor Model 398R-54-62 to Analyzer Model SoluComp. Note: Sensor Model 398R-54 can also be wired as shown above, but customer must prepare BNC as shown in Figure 3-22. 24 A MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40308131 REV. A FIGURE 3-24. BNC Preparation Instructions 25 MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR DWG. NO. 40308132 FIGURE 3-25. Extension Cable Preparation 26 REV. A MODEL 398R/398RVP pH/ORP SECTION 3.0 WIRING THE MODEL 398R SENSOR FIGURE 3-26. Wiring Model 398R-54-61 to Model Xmt-P-HT-10 FIGURE 3-27. Wiring Model 398R-54-62 to Model Xmt-P-HT-10 27 MODEL 398R/398RVP pH/ORP SECTION 4.0 WIRING THE MODEL 398RVP SENSOR SECTION 4.0 WIRING THE MODEL 398RVP SENSOR 4.1 GENERAL Make electrical connections, as shown in Figures 4-1 through 4-19 using the following guidelines: 5. Run signal cable in a dedicated conduit away from AC power lines. 1. Pay particular attention to the analyzer or transmitter model number when following details on the wiring diagrams to ensure that the connections are made to the proper terminals. NOTE For maximum EMI/RFI protection when wiring from the sensor to the junction box, the outer braid of the sensor should be connected to the outer braid of the extension cable. The outer braid of the extension cable to the instrument must be terminated at earth ground or by using an appropriate metal cable gland fitting that provides a secure connection tot he instrument cable. 2. Use mating VP connector cable PN 23645-06 or PN 23645-07. 3. Use Rosemount custom cable PN 9200273 (unprepped), 236446-01 (prepped), or PN 9200254 (unprepped) to connect the transmitter or analyzer to remote or sensor-mounted junction boxes. 4. The maximum distance from the sensor to the analyzer is 15 ft without an integral sensor preamplifier. 4.2 WIRING DIAGRAMS. For wiring diagram information, refer to Table 4-1. TABLE 4-1. Wiring Guide for Model 398RVP Sensor VP CONNECTOR CABLE 23645-07 23645-07 23645-07 23645-07 23645-07 23645-07 23645-06 23645-07 23645-07 23645-07 ANALYZER/TRANSMITTER 54 81 3081/4081 2081 2700 1054 1054A, 1054B, 2054 1181 SoluComp SoluComp II (1055) VP CONNECTOR CABLE 23645-06 23645-06 23645-06 23645-06 23645-07 23645-07 23645-07 ANALYZER/TRANSMITTER 1181, 1050, 1060, 1003, 1023 1054A, 1054B, 2054 2081 1054 54 81 3081, 4081 28 FIGURE # 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-11 4-12 4-19 REMOTE JUNCTION BOX 23309-03 23309-03 23309-03 23309-04 23555-00 23555-00 23555-00 FIGURE # 4-9 4-10 4-13 4-14 4-15 4-16 4-17 MODEL 398R/398RVP pH/ORP SECTION 4.0 WIRING THE MODEL 398RVP SENSOR FIGURE 4-1. Wire Configurations for Variopol Cable PN 23645-06 and PN 23645-07 FIGURE 4-2. Wiring Details for Sensor Model 398RVP to Analyzer Model 54/54e FIGURE 4-3. Wiring Details for Sensor Model 398RVP to Analyzer Model 81 29 MODEL 398R/398RVP pH/ORP FIGURE 4-4. Wiring Details for Sensor Model 398RVP to Analyzer Models 3081, 4081, & 5081 SECTION 4.0 WIRING THE MODEL 398RVP SENSOR FIGURE 4-5. Wiring Details for Sensor Model 398RVP to Analyzer Model 2081 FIGURE 4-6. Wiring Details for Sensor Model 398RVP to Analyzer Model 2700 30 MODEL 398R/398RVP pH/ORP SECTION 4.0 WIRING THE MODEL 398RVP SENSOR FIGURE 4-7. Wiring Details for Sensor Model 398RVP to Analyzer Model 1054 FIGURE 4-8. Wiring Details for Sensor Model 398RVP to Analyzer Model 1054A/B and 2054 FIGURE 4-9. Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN 23309-03 to Analyzer Models 1181, 1060, 1003, 1023 FIGURE 4-10. Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN 23309-04 to Analyzer Models 1054A/B and 2054 31 MODEL 398R/398RVP pH/ORP 32 SECTION 4.0 WIRING THE MODEL 398RVP SENSOR FIGURE 4-11. Wiring Details for Sensor Model 398RVP to Analyzer Model 1181 FIGURE 4-12. Wiring Details for Sensor Model 398RVP to Analyzer Model SCL-(P/Q) FIGURE 4-13. Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN 23309-03 to Analyzer Model 2081 FIGURE 4-14. Wiring Details for Sensor Model 398RVP thru Remote Junction Box PN 23309-04 to Analyzer Model 1054 MODEL 398R/398RVP pH/ORP SECTION 4.0 WIRING THE MODEL 398RVP SENSOR FIGURE 4-15. Wiring Details for Sensor Model 398RVP thru Remote Junction Box to Analyzer Model 54 or 54e FIGURE 4-16. Wiring Details for Sensor Model 398RVP thru Remote Junction Box to Analyzer Model 81 FIGURE 4-17. Wiring Details for Sensor Model 398RVP thru Remote Junction Box to Analyzer Models 3081, 4081, 5081 33 MODEL 398R/398RVP pH/ORP SECTION 4.0 WIRING THE MODEL 398RVP SENSOR DWG. NO. 40308132 FIGURE 4-18. Extension Cable Preparation 34 REV. A MODEL 398R/398RVP pH/ORP SECTION 4.0 WIRING THE MODEL 398RVP SENSOR FIGURE 4-19. Wiring Model 398RVP-54 to Model 1055-22-32 FIGURE 4-20. Wiring Model 398RVP-54 to Model 1055-22-32 35 MODEL 398R/398RVP pH/ORP SECTION 5.0 CALIBRATION SECTION 5.0 CALIBRATION 5.1 GENERAL INFORMATION 1. New sensors must be calibrated before use. 2 Regular recalibration is also necessary and is determined by the user. 3. The use of a two-point buffer calibration is always recommended. 4. Refer to the transmitter/analyzer instruction manual for more specific calibration procedures. 5.2 USE OF CALIBRATION BUFFERS (STANDARDS) 1. Good buffers lead to good calibrations: A pH measurement is only as good as the calibration, and the calibration is only as good as the buffers used. A careful buffer calibration is the first step in making an accurate pH measurement. 2. Use appropriate buffers: Calibrate with buffers having pH values that bracket the pH of the process. For example, if the pH is between 8 and 9, calibrate with pH 7 and 10 buffers. Commercial buffers for intermediate range pH are readily available. 3. Sensor and buffers must be at the same temperature: Allow time for the sensor and buffers to reach the same temperature. If the sensor was just removed from a process having a temperature more than 10°C different from the buffer, allow at least 20 minutes. 4. Buffers must be at process temperature: For best results, calibrate with buffers having the same temperature as the process. If the buffer and process temperature differ by more than about 15°C an error as great as 0.1pH may result. 5. Be careful using buffers at very high temperatures: Protect the solution from evaporation. Evaporation changes the concentration of the buffer and its pH. Be sure the pH of the buffer is defined at high temperatures. The pH of many buffers is undefined above 60°C. Finally, no matter what the temperature is, allow the entire measurement cell, sensor and solution, to reach constant temperature before calibrating. 6. The pH of a buffer changes with temperature: The pH of a buffer is a function of temperature. The pH of alkaline buffers depends more strongly on temperature than the pH of acidic or neutral buffers. Most process pH instruments, including those manufactured by Rosemount Analytical, have an auto calibration feature. The instrument recognizes the buffer being used and automatically corrects for the change in buffer pH with temperature. If the instrument does not perform the correction, the user must enter the appropriate value. Buffer manufacturers usually list the temperature dependence of the buffer on the label. 7. Buffers have limited shelf lives: Do not use a buffer if the expiration date has passed. Store buffers at controlled room temperature. 8. Do not reuse buffers: Do not return used buffer to the stock bottle. Discard it. 9. Protect buffers from excessive exposure to air: Atmospheric carbon dioxide lowers the pH of alkaline buffers. Other trace gases commonly found in industrial environments, for example, ammonia and hydrogen chloride, also affect the pH of buffers. Molds, from airborne spores, grow readily in neutral and slightly acidic buffers. Mold growth can substantially alter the pH of a buffer. 10. Clean the sensor before using buffers: Rinse the sensor with deionized water before placing it in a buffer. Remove excess water from the sensor by gently daubing it with a clean tissue. Do not wipe the sensor. Wiping may generate a static charge, leading to noisy readings. The static charge may take hours to dissipate. A few drops of deionized water carried with the sensor into the buffer will not appreciably alter the pH. 36 MODEL 398R/398RVP pH/ORP SECTION 5.0 CALIBRATION 5.3 TWO-POINT BUFFER CALIBRATION: GENERAL INSTRUCTIONS. 1. Remove the protective vinyl cap from the sensor tip. 2. Rinse the sensor and immerse it in the first buffer. Ensure that the glass bulb and the temperature element are completely submerged by keeping the sensor tip about 3 inches below the liquid level. Swirl the sensor to dislodge trapped air bubbles. Do not allow the weight of the sensor to rest on the glass bulb. 3. Once the reading is stable, enter the buffer value in the analyzer. If the analyzer does not correct for changes in buffer pH with temperature, be sure to enter the temperature-corrected value. 4. Remove the sensor from the first buffer. Rinse the sensor and place it in the second buffer. Follow the same precautions given in step 2. 5. Once the reading is stable, enter the buffer value in the analyzer. If the analyzer does not correct for changes in buffer pH with temperature, be sure to enter the temperature-corrected value. 6. After calibration, note the sensor slope. Slope has units of mV per unit change in pH. An ideal sensor has a slope of 59 mV/pH at 25°C. Slope decreases as the sensor ages. Once the slope drops to between 47 and 49 mV/pH, the sensor should be replaced. 7. Remove the sensor from buffer 2 and return it to the process liquid. 5.4 pH STANDARDIZATION: GENERAL INSTRUCTIONS Standardization means making the process instrument match the reading from a second pH meter. The second pH reading is usually made on a grab sample. 1. Take the sample from a point as close as possible to the process sensor. To avoid starving the process sensor, use a downstream sample point. 2. Wait until the process pH is constant or, at worst, slowly drifting before taking the grab sample. 3. To ensure that measured pH is truly the pH of the process liquid, determine the pH of the grab sample immediately. pH is a function of temperature. If the temperature of the process differs from ambient, measure the pH of the grab sample before its temperature changes. Some process liquids are poorly buffered. The pH of the sample may change significantly upon exposure to air or to the sample container. To avoid deterioration of the sample, measure the pH immediately. 4. Following the instructions in the instrument manual, adjust the process reading to the value measured on the grab sample. 5.5 ORP STANDARDIZATION: GENERAL INSTRUCTIONS There are relatively few ORP calibration standards available. The most popular one is a solution containing 0.1 M iron (II) and 0.1 M iron (III) in 1 M sulfuric acid. The standard is available from Rosemount Analytical as PN R50816OZ. The poten-tial of the solution measured against a silver-silver chloride reference electrode is 475 ±20 mV at 25°C. 1. Rinse the sensor with deionized water and place it in the ORP standard along with a reliable ther-mometer. Submerge the sensor tip at least three inches below the surface of the liquid. Swirl the sensor to dislodge trapped bubbles. Adjust the temperature of the standard to 25 ±5°C. 2. Wait until temperature and ORP readings are stable. 3. Following the instructions in the instrument analyzer, store ORP value (475 mV) in memory. 4. Remove the sensor from the ORP standard, rinse it, and return it to the process fluid. 37 MODEL 398R/398RVP pH/ORP SECTION 6.0 MAINTENANCE SECTION 6.0 MAINTENANCE 6.1 Maintenance. The frequency at which a sensor should be inspected, cleaned, and calibrated can be determined only by experience. Generally, the greater the tendency of the process liquid to coat or foul the sensor, the more frequently maintenance should be done. Because the Model 398R and 398RVP sensors resist fouling, they usually require maintenance less often than other pH (or ORP) sensors. Sensors exposed to extreme pH values or to high temperature require more frequent inspection than sensors installed in less severe environments. The best way to evaluate a sensor is to check its performance in buffers. If the sensor cannot be calibrated or has low slope, it is dirty or has failed. Refer to the troubleshooting guide in the instrument manual and in this manual for assistance. 6.2 Sensor Removal. Please refer to the appropriate paragraph for instructions regarding removal of the sensor for periodic maintenance. 6.2.1 Retractable Version. WARNING System pressure may cause the sensor to blow out with great force unless care is taken during removal. Make sure the following steps are adhered to. A. Model 398R-21 and 398RVP-21 (21” tube) 1. Be certain system pressure at the sensor is below 64 psig before proceeding with the retraction. It is also recommended that the personnel wear a face shield and have a stable footing. Refer to Figure 6-1. Push in on the cable end or the top of the junction box and slowly loosen the hex nut (B) of the process end male connector (A). FIGURE 6-1. Example of Sensor Tube Replacement 38 MODEL 398R/398RVP pH/ORP SECTION 6.0 MAINTENANCE B. Model 398R-25 and 398RVP-25 (36” tube) 2. Be certain that pressure at the sensor is below 35 psig before proceeding with the retraction. It is also recommended that the personnel wear a face shield and have a stable footing. Refer to Figure 6-1. Push in on the cable end or the top of the junction box and slowly loosen the hex nut (B) of the process end male connector (A). CAUTION Do not remove nut at this time. 3. When the hex nut is loose enough, slowly ease the sensor back completely until the retraction stop collar (mechanical safety stop) is reached. CAUTION Failure to withdraw the sensor completely may result in damage to the sensor when the valve is closed. 4. Close the ball valve slowly. If there is resistance, the valve may be hitting the sensor. Double check that the sensor has been retracted to the retraction stop collar. WARNING Before removing the sensor from the ball valve, be absolutely certain that the ball valve is fully closed. Leakage from the male connector threads may indicate that the male connector is still under pressure. Leakage through a partially open valve could be hazardous, however with the ball valve closed, some residual process fluid may leak from the connector's pipe threads. 5. The Male Connector Body (A) may now be completely unthreaded from the reducing coupling and the sensor removed for servicing. CAUTION If the male connector leaks during insertion or retraction, replace the O-ring (PN 9550167) in the male connector (A). 6.3 Cleaning Procedures - pH Sensors. To remove the sensor from the process piping, follow the instructions in Section 6.2. CAUTION Only persons thoroughly familiar with the procedure for diluting concentrated hydrochloric acid should prepare the solution. Dilute the acid in a fume hood or in a well-ventilated area. Point the acid bottle away from people when opening it. Wear appropriate safety equipment, including chemical goggles and gloves. Do not let acid touch the skin or clothing. If acid solutions contact the skin or eyes, rinse thoroughly with water. Seek medical assistance. PROBLEM CLEANING SUGGESTIONS Loose scale or debris Use a stream of water from a wash bottle to rinse away solids from the tip of the sensor. If water does not work, gently wipe the glass bulb and liquid junction with a soft cloth, tissue, cotton-tipped swab, or a soft bristle brush. Oil and grease Wash the glass bulb with mild detergent solution and rinse thoroughly with water. Hard scale (carbonate and sulfate scales and corrosion products) If wiping the sensor tip with a tissue or cotton swab does not remove the scale, soak the the glass bulb ONLY in a solution of 5% hydrochloric acid. To prepare the acid solution, add 15 mL of concentrated hydrochloric acid to 85 mL of water with continuous stirring. See CAUTION below. Keep the acid away from the liquid junction. Rinse the sensor thoroughly with deionized water. Some scales (for example, calcium sulfate) cannot be removed easily with acid. Soaking the glass bulb in a 2% solution of disodium EDTA for 20 minutes may be helpful. 39 MODEL 398R/398RVP pH/ORP SECTION 6.0 MAINTENANCE When using acid or alkaline solvents, be careful to keep the solvent away from the liquid junction. See Figure 6-2. If the cleaning solvent contacts the junction, hydrogen ions (acid solvent) or hydroxide ions (alkaline solvent) will diffuse into the junction. Because hydrogen and hydroxide ions have much greater mobility than other ions, they produce a large junction potential. When the electrode goes back in service, the hydrogen or hydroxide ions slowly diffuse out of the junction, causing the liquid junction potential and the pH reading to drift. It may take hours or days for the reading to stabilize. Always recalibrate the sensor after cleaning. If the sensor was cleaned with detergent or acid, soak the sensor in pH 4 or pH 7 buffer for at least an hour before calibrating. 6.4 Cleaning Procedures - ORP Sensors Clean platinum ORP electrodes by using a tissue to rub the metal surface with a paste of baking soda (sodium bicarbonate). A clean platinum electrode is bright and shiny. Figure 6-2. Model 398R pH Sensor The figure shows the tip of the Model 398R pH sensor. The bottom of the liquid junction is about even with the top of the wings that form the slotted tip. Keep acidic and alkaline solvents away from the liquid junction. If acids or bases get into the junction, subsequent pH readings may drift for several hours. 6.5 Checking the Reference Electrode Some processes contain substances, for example, sulfides, that poison the reference electrode. Poisoning alters the electrode potential. For example, sulfide poisoning converts the reference electrode from a silver/silver chloride electrode into a silver/silver sulfide electrode, causing a shift in potential of several hundred millivolts. A good way to check for poisoning is to compare the voltage of the reference electrode with a silver/silver chloride electrode that is known to be good. The reference electrode from a new sensor is the best choice. To check the suspect electrode, place both sensors in a beaker containing buffer or a solution of potassium chloride. Connect the reference leads to a voltmeter and measure the potential difference. If the suspect electrode is good, the difference should be no more than about 20 mV. Refer to Figure 6-3. A poisoned reference electrode usually requires replacement. A laboratory silver/silver chloride reference electrode can be used in place of the second sensor. All Rosemount Analytical pH sensors have a silver/silver chloride reference, and most sensors use gelled saturated potassium chloride for the fill. The potentials of a good sensor reference electrode and a saturated silver/silver chloride laboratory electrode will agree within about 20 mV. 40 Figure 6-3. Checking the Potential of the Reference Electrode. Refer to the wire function diagrams in Figure 2-6 to identify the reference lead. For sensors with a BNC connection, the reference is the outside of the BNC connector. For sensors without a BNC, the reference is the clear wire grouped with the orange pH/ORP lead. MODEL 398R/398RVP pH/ORP 6.6. Rejuvenating Reference Electrodes Occasionally, a poisoned or plugged reference electrode can be reconditioned. Although the electrode seldom recovers completely, the procedure might extend the life of the sensor by a few weeks. a. Clean the sensor as thoroughly as possible. b. Soak the sensor for several hours in a hot (NOT BOILING) 3% potassium chloride solution. Prepare the solution by dissolving 3 g of potassium chloride in 100 mL of water. c. Soak the sensor in pH 4 buffer at room temperature overnight. d. Calibrate the sensor in buffers and retest it in the process liquid. 6.7. Temperature Element SECTION 6.0 MAINTENANCE TABLE 6-1. Resistance as a Function of Temperature for Selected RTDs. Temperature °C 0 10 20 25 30 40 50 60 70 80 90 100 Resistance (Ohms) ±1% 3K PT-100 2670 100.0 2802 103.8 2934 107.7 3000 109.6 3066 111.5 3198 115.4 3330 119.2 3462 123.1 3594 126.9 3726 130.8 3858 134.6 3990 138.5 The Model 398R and 398RVP pH sensors produce a voltage which the instrument converts to pH using a temperature-dependent factor. A Pt 100 or a Balco 3K RTD built into the sensor measures temperature. To permit cor-rection for changes in lead resistance with temperature, a three-wire configuration (Figure 6-4) is used. To check the RTD, disconnect the leads and measure the resistances shown. The measured resistance should agree with the value in the table to within about ±1%. If the measured resistance is appreciably dif-ferent (between 1 and 5%), the discrepancy can be calibrated out. See the instrument instruction manual. 6.8. Sensor Tube Replacement When Used With A Sensor Head Junction Box Figure 6-4. Three-wire RTD circuit Consult Table 6.1 (above) for temperature-resistance data. Lead resistance is about 0.05 ohm/ft at 25°C. Therefore, 15 ft of cable increases the resistance by about 1.5 ohm. The resistance between the RTD return and RTD sense leads should be less than 2 ohms. If a connection is open or shorted and should not be, replace the sensor. If the measured resistance is greatly in error, replace the sensor. Replacement of the retraction versions sensor tube assembly involves the removal and installation of two sets of male connectors: One at the process end of the sensor, and the other at the junction box end (See Figure 6-1 and Figure 6-5). Refer to Section 6.2 for proper removal of the sensor from process. 1. 2. 3. Remove sensor from process before proceeding. The junction box with attached male connector must be recovered from the old sensor for reuse. Unscrew the junction box cover and set aside. Disconnect electrical connections from printed circuit board inside junction box. Disconnect BNC connector to preamp. Unscrew hex nut (F) from male connector body (E). Separate junction box from used sensor. Set aside. Pry off split ferrule from sensor and set aside for reuse. Remove hex nut (F) and set aside for reuse. Check that the internal O-ring is in place in the male connector body (E) attached to the junction box. Remove hex nut (B) from male connector body (A) at process end of sensor and set aside. Slide the Teflon ferrule and the male connector off sensor in the direction of junction box and set NOTE If stainless steel ferrule was used, male connector body (A) will have to be discarded with the sensor tube. 41 MODEL 398R/398RVP pH/ORP 4. SECTION 6.0 MAINTENANCE Discard used O-ring from male connector body (A). Coat new O-ring with a thin film of the O-ring lubricant provided. Position it in the machined O-ring groove in place of the discarded O-ring. CAUTION Make sure lubricant does not contact any part of the sensor tip particularly the glass bulb. 5. Cover the 1" MNPT pipe threads of the male connector body (A) with Teflon tape (not provided) to protect them from galling during reinstallation. 6. Pass the wires from the new sensor through the process end male connector (A). Make sure that the beveled edge of the ferrule faces the process end of the sensor. Snug the hex nut (B) to keep it in place. Do not tighten down fully on the hex nut at this time. 7. Pass the wires from the new sensor through the hex nut (F), the split ferrule (from the old sensor), male connector body (E), O-ring, and through the junction box from the “neck” opening and out to the printed circuit board in the junction box. Butt the ferrule’s beveled edge and the sensor tube against the junction male connector (E). Screw the hex nut (F) by hand until the tube is “locked” into the male connector body. Make sure that the male connector body (E) is sufficiently tightened. The sensor will “click” into place by pulling the sensor tube away from the junction box, but will not move from side to side or pull clear of the male connector. If the sensor tube is correctly attached to the junction box, wrench tighten hex nut (F) on male connector body (E). See Figure 6-1. Do not put the sensor tube in a vise or use a pipe wrench to tighten the hardware as these will damage the sensor. If sensor tube is not correctly attached to the junction box, loosen hex nut (F) and repeat. 8. Connect the sensor wires to the terminals on the printed circuit board in the junction box in the manner recommended on the junction box cover,and reattach the BNC connector to the preamp. Screw on the cover of the junction box aside. Discard sensor tube. 9. Insert the sensor in the process fitting. Stop it against the closed ball valve. Slide the process-end male connector down the sensor tube to mate with the process fitting. Tighten the male connector into the process fitting. 10. Pull back hard on the sensor assembly, as if trying to remove the sensor, to be certain that the sensor cannot come free from the valve assembly and male connector. The built-in retraction stop collar at the end of the sensor will butt against the shoulder of the male connector. 11. Open ball valve and position the sensor at the desired insertion depth and orientation. Using a crescent or open end wrench, tighten the hex nut (B) to secure the sensor in place. See Figure 6-5. NOTE A stainless steel ferrule is available if the Teflon ferrule does not adequately grip. Be careful and avoid over tightening. This can damage the sensor tube. CAUTION If the male connector leaks during insertion or retraction, replace the O-Ring (PN 9550167) in the male connector body (A). If the sensor is to be stored, the rubber boot should be filled with 7pH buffer solution and replaced on sensor tip until ready to use. FIGURE 6-5. Male Connector Tightening Diagram 42 MODEL 398R/398RVP pH/ORP SECTION 7.0 TROUBLESHOOTING SECTION 7.0 TROUBLESHOOTING TROUBLESHOOTING. Table 7-1, below, lists common problems, causes and remedies typically encountered in process measurement. For more specific troubleshooting information, please refer to the appropriate analyzer/ transmitter manual. TABLE 7-1. Troubleshooting PROBLEM/SYMPTOM PROBABLE CAUSE REMEDY pH value from sensor will not stabilize for calibration, even though sensor seemed to work okay in process stream Dirty sensor See Section 6.3, Cleaning Procedures. Broken wire Check wire integrity at instrument end of the sensor cable. Miswired sensor Check wiring diagrams for proper wiring to appropriate analyzer. Buffers are old or contaminated Retry calibration with fresh buffers. Glass electrode failure The glass may be cracked. Check the glass impedance value. If it is above 20 megohms, glass is not cracked. Air bubbles trapped on outside surface of glass Gently swirl sensor to remove any air bubbles that may have formed when sensor was placed into calibration beaker. pH sensor bulb has dried out in storage Soak sensor in pH 4 buffer for several hours. Then retry calibration. Miswired sensor Check wiring diagrams for proper wiring to appropriate analyzer. Buffers are old or contaminated Retry calibration with fresh buffers. Air bubbles inside glass bulb Gently shake down sensor to remove any air bubbles that have formed inside the glass bulb measurement area. Air bubbles trapped on outside surface of glass Gently swirl sensor to remove any air bubbles that may have formed when sensor was placed into calibration beaker. Buffers are old or contaminated 1. Retry calibration with fresh buffers. 2. Make sure that the temperature of the buffer solutions are the same temperature as the sensor. 3. Some 10 pH buffers are inaccurate (because of age or manufacturing procedures) and could cause high slope error. In this case, try another pH 10 buffer or buffer calibrate with another value of pH buffer. Calibration technique or procedure 1. Inaccurate procedure or technique. 2. Sensor must be cooled to same temperature as buffer solutions. 3. Sensor must continue to be immersed in buffer solution until reading has stabilized. pH value from new sensor will not stabilize for calibration After completing calibration procedures, slope is high (a high slope value is any value above 59.1 mV) 43 MODEL 398R/398RVP pH/ORP SECTION 7.0 TROUBLESHOOTING TABLE 7-1. Troubleshooting (continued) PROBLEM/SYMPTOM PROBABLE CAUSE REMEDY After completing calibration procedures, slope is low (a low slope value is any value below 48 mV) Aged glass electrode Replace sensor if glass impedance is above 800 megohms. High temperature exposure Replace sensor; high temperature has affected the sensor much like aging glass. Electrode is coated See Section 6.3 for proper sensor cleaning. After cleaning, the glass impedance value will dramatically drop to a value between 20 and 800 megohms. Broken wire Check integrity of wires at instrument end of the sensor cable. Miswired sensor Check wiring diagrams for proper wiring to appropriate analyzer. Buffers are old or contaminated Retry calibration with fresh buffers. Glass electrode is cracked The glass may be cracked. Check the glass impedance value. If it is above 20 megohms, the glass is not cracked. Defective preamplifier If it is a plug-in preamplifier in junction box or in instrument, replace preamplifier unit. If preamplifier is integral to sensor, replace entire sensor. Electrode is coated See Section 6.3 for proper sensor cleaning. After cleaning, glass impedance value will dramatically drop to a value between 20 and 800 megohms. Glass electrode has hairline crack The glass may be cracked. Check the glass impedance value. If it is above 20 megohms, glass is not cracked. pH reading between 3 and 6 pH regardless of actual pH of solution or sample Glass electrode is cracked Replace sensor. pH reading is off scale Defective preamplifier If it is a remote preamplifier, replace the preamplifier unit. If preamplifier is integral to sensor, replace entire sensor. T.C. element shorted Check T.C. element (see Section 6.5) and replace sensor if defective. Sensor is not in process or sample stream is low Make sure sensor is in process with sufficient sample stream (refer to Section 2.0 for installation details). Glass electrode is cracked or reference element is shorted Replace sensor pH display on instrument jumps widely while in auto T.C. mode T.C. element is shorted Check T.C. element (see Section 6.5) and replace sensor if defective. Span between buffers is extremely short in auto T.C. mode T.C. element is open Check T.C. element (see Section 6.5) and replace sensor if defective. While sensor is in the process, the pH reading is sluggish or slow to change Continued on following page 44 MODEL 398R/398RVP pH/ORP SECTION 7.0 TROUBLESHOOTING TABLE 7-1. Troubleshooting (continued) PROBLEM/SYMPTOM PROBABLE CAUSE REMEDY While pH sensor is in process, pH reading is not stable, fluctuates too much Air bubbles trapped on glass bulb Remount sensor in a part of the process stream where the flow is less turbulent. Sensor is mounted too close to pump Remount sensor in a part of the process stream where the pumping effect is less burdensome on the sensor. Sensor is mounted too close to chemical addition, reaction is taking place at this point and pH is actually changing all the time Remount sensor in a part of the process stream where the reaction has stabilized. Then the pH reading will not seem to fluctuatetoo much. pH value of process sensor in buffer solution doesn’t match the pH value stated on label of the buffer solutions Temperature of the sensor is not the same as the pH buffers Since the pH value of mixtures changes with temperature, the temperature of the pH sensor and the buffer solutions must be the same. Otherwise, pH value will not match buffer value. pH value of process sensor in process grab sample doesn’t match the grab sample pH value Temperature of the process sensor is not the same as the temperature of the grab sample Since the pH value of mixtures changes with temperature, the temperature of the pH sensor and the buffer solutions must be the same. Otherwise, pH value will not match buffer value. Once sensor has been properly calibrated and placed in the process stream, pH value shifts 0.1 to 0.2 pH units or more within a short period of time. Reference is becoming contaminated Although an extremely rare case for any TUpH reference, the reference can become contaminated with certain substances. If this is the case, consult Rosemount Analytical for process stream evaluation. Process solution ground loop If sensor has been verified to work in buffers, check for ground loops in the following manner: 1. Connect a heavy gauge wire to the process piping or in process tank. 2. Place loose end of wire into beaker with buffer solution and pH sensor. If buffer value changes the same way that is seen the the process, then a ground loop has been confirmed. If symptoms do not develop but problem still persists, a ground loop is not ruled out. Consult Rosemount Analytical for further help with ground loop problems. 45 MODEL 398R/398RVP pH/ORP SECTION 8.0 RETURN OF MATERIAL SECTION 8.0 RETURN OF MATERIAL 8.1 GENERAL. 8.3 NON-WARRANTY REPAIR. To expedite the repair and return of instruments, proper communication between the customer and the factory is important. Before returning a product for repairs, call 1-949-757-8500 for a Return Materials Authorization (RMA) number. The following is the procedure for returning for repair instruments that are no longer under warranty: 1. Call Rosemount Analytical for authorization. 2. Supply the purchase order number, and make sure to provide the name and telephone number of the individual to be contacted should additional information be needed. 3. Do Steps 3 and 4 of Section 8.2. 8.2 WARRANTY REPAIR. The following is the procedure for returning instruments still under warranty: 1. Call Rosemount Analytical for authorization. 2. To verify warranty, supply the factory sales order number or the original purchase order number. In the case of individual parts or sub-assemblies, the serial number on the unit must be supplied. 3. Carefully package the materials and enclose your “Letter of Transmittal” (see Warranty). If possible, pack the materials in the same manner as they were received. 4. Send the package prepaid to: Rosemount Analytical Inc., Uniloc Division Uniloc Division 2400 Barranca Parkway Irvine, CA 92606 Attn: Factory Repair RMA No. ____________ Mark the package: Returned for Repair Model No. ____ 46 NOTE Consult the factory for additional information regarding service or repair. WARRANTY Seller warrants that the firmware will execute the programming instructions provided by Seller, and that the Goods manufactured or Services provided by Seller will be free from defects in materials or workmanship under normal use and care until the expiration of the applicable warranty period. Goods are warranted for twelve (12) months from the date of initial installation or eighteen (18) months from the date of shipment by Seller, whichever period expires first. Consumables, such as glass electrodes, membranes, liquid junctions, electrolyte, o-rings, catalytic beads, etc., and Services are warranted for a period of 90 days from the date of shipment or provision. Products purchased by Seller from a third party for resale to Buyer ("Resale Products") shall carry only the warranty extended by the original manufacturer. Buyer agrees that Seller has no liability for Resale Products beyond making a reasonable commercial effort to arrange for procurement and shipping of the Resale Products. If Buyer discovers any warranty defects and notifies Seller thereof in writing during the applicable warranty period, Seller shall, at its option, promptly correct any errors that are found by Seller in the firmware or Services, or repair or replace F.O.B. point of manufacture that portion of the Goods or firmware found by Seller to be defective, or refund the purchase price of the defective portion of the Goods/Services. All replacements or repairs necessitated by inadequate maintenance, normal wear and usage, unsuitable power sources, unsuitable environmental conditions, accident, misuse, improper installation, modification, repair, storage or handling, or any other cause not the fault of Seller are not covered by this limited warranty, and shall be at Buyer's expense. Seller shall not be obligated to pay any costs or charges incurred by Buyer or any other party except as may be agreed upon in writing in advance by an authorized Seller representative. All costs of dismantling, reinstallation and freight and the time and expenses of Seller's personnel for site travel and diagnosis under this warranty clause shall be borne by Buyer unless accepted in writing by Seller. Goods repaired and parts replaced during the warranty period shall be in warranty for the remainder of the original warranty period or ninety (90) days, whichever is longer. This limited warranty is the only warranty made by Seller and can be amended only in a writing signed by an authorized representative of Seller. Except as otherwise expressly provided in the Agreement, THERE ARE NO REPRESENTATIONS OR WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, AS TO MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, OR ANY OTHER MATTER WITH RESPECT TO ANY OF THE GOODS OR SERVICES. RETURN OF MATERIAL Material returned for repair, whether in or out of warranty, should be shipped prepaid to: Emerson Process Management Liquid Division 2400 Barranca Parkway Irvine, CA 92606 The shipping container should be marked: Return for Repair Model _______________________________ The returned material should be accompanied by a letter of transmittal which should include the following information (make a copy of the "Return of Materials Request" found on the last page of the Manual and provide the following thereon): 1. 2. 3. 4. 5. Location type of service, and length of time of service of the device. Description of the faulty operation of the device and the circumstances of the failure. Name and telephone number of the person to contact if there are questions about the returned material. Statement as to whether warranty or non-warranty service is requested. Complete shipping instructions for return of the material. Adherence to these procedures will expedite handling of the returned material and will prevent unnecessary additional charges for inspection and testing to determine the problem with the device. If the material is returned for out-of-warranty repairs, a purchase order for repairs should be enclosed. The right people, the right answers, right now. ON-LINE ORDERING NOW AVAILABLE ON OUR WEB SITE http://www.raihome.com Specifications subject to change without notice. 8 Credit Cards for U.S. Purchases Only. Emerson Process Management 2400 Barranca Parkway Irvine, CA 92606 USA Tel: (949) 757-8500 Fax: (949) 474-7250 http://www.raihome.com © Rosemount Analytical Inc. 2011